Fibocom SC806 Скачать руководство пользователя страница 45

Страница: 45 / 70

The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval.

SC806Hardware User ManualPage45 of 70

195

MIC3_P

Auxiliary MIC single-end input

210

MIC_BIAS1

MIC bias voltage

Note:

1) The MIC bias circuit has been added to the SC806 and no external addition is required.

2) Add 100K resistor to ground for MIC2_P

3) The SPK is a configured class D amplifier and cannot be connected to an external amplifier. It is recommended

to connect 8 ohm speakers. There is a high requirement for sound amplitude of loud speaker, and the amplifier can

be connected to the headphone for output.

4) Reduce noise and improve audio quality. The following approaches are recommended:



Keep audio PCB route away from the antenna and high-frequency digital signal



Reserve LC filter circuit in audio circuit to prevent EMC



Audio route need to be masked

Antenna Interface

The SC806 supports 2/3/4G main antenna/diversity receiving antenna, WIFI/BT antenna, and GNSS antenna.

4.1

MAIN/DRXAntenna

The SC806 provides two 2G/3G/4G antenna interfaces. The ANT_MAIN is used to receive and transmit RF

signal, and the ANT_DRX is used for diversity reception.

Table26MAIN/DRX antenna interface definition

Pin No.

Pin Name

I/O

Description

Note

ANT_MAIN

I/O

2G/3G/4G antenna interface

131

ANT_DRX

Diversity reception antenna

4.1.1

Operating bands

Table27Module operating band

Band

Mode

Tx (MHz)

Rx (MHz)

Band 2

LTE FDD/WCDMA/GSM

1850-1910

1930-1990

Band 4

LTE FDD/WCDMA

1710-1755

2110-2155

Содержание SC806







































































Результаты поиска

Содержание SC806

Отзывы:

Бренды по названию

Популярные бренды

Fibocom SC806, Руководство пользователя по оборудованию

Результаты поиска

Содержание SC806

Отзывы:

Бренды по названию

Популярные бренды