FiberHome CiTRANS R820 Скачать руководство пользователя страница 68

Страница: 68 / 126

CiTRANS R820 Edge Router Hardware Description

Collects and distribute single-card configurations, alarms, and

performance data.

Service access and switching functions

Provides a switching capacity of 26G.

Processes packets, for example, identifies, terminates, encapsulates, and

discards packets and performs unicast and multicast processing for

packets.

Implements different types of protection, such as 1:1 tunnel, LAG, PW

redundancy, LDP FRR, IP FRR, VPN FRR, MPLS TE FRR, and VRRP.

Supports OAM at four layers: link layer, tunnel layer, PW layer, and

Ethernet service layer.

Supports the hierarchical QoS function.

Time and clock synchronization functions

Provides the 25 MHz (single-ended TTL) system clock and the 8 kHz

frame timing clock required by each card.

Supports synchronous Ethernet interfaces.

Supports the interface for synchronizing external frequencies and

implements input and output of E1 HDB3 or E1 Hz clocks.

Support IEEE 1588v2.

Supports the external time interface TOD and can use this interface to

issue or receive the time.

Panel Description

Figure 5-6 shows the panel of the SCUS1/SCUS2/SCUS3 card.

5-8

Version: A

Содержание CiTRANS R820































































































































Результаты поиска

Содержание CiTRANS R820

Отзывы:

Похожие инструкции для CiTRANS R820

Бренды по названию

Популярные бренды

FiberHome CiTRANS R820, Описание аппаратуры

Результаты поиска

Содержание CiTRANS R820

Отзывы:

Похожие инструкции для CiTRANS R820

Бренды по названию

Популярные бренды