manualshive.com logo in svg

FIBARO DOOR/WINDOW SENSOR 2, Руководство по эксплуатации, Страница: 15 / 16

Поделиться
Скачать
FIBARO DOOR/WINDOW SENSOR 2 Скачать руководство пользователя страница 15

15

REGULATIOnS

#9: Regulations

This device complies with Part 15 of the FCC Rules 

Operation is subject to the following two conditions:

1. This device may not cause harmful interference

2. This device must accept any interference received, including interfe-

rence that may cause undesired operation. This equipment has been 

tested and found to comply with the limits for a Class B digital device, 

pursuant to part 15 of the FCC Rules. These limits are designed to pro-

vide reasonable protection against harmful interference in a residen-

tial installation. This equipment generates, uses and can radiate radio 

frequency energy and, if not installed and used in accordance with the 

instructions, may cause harmful interference to radio communications. 

However, there is no guarantee that interference will not occur in a par-

ticular installation. If this equipment does cause harmful interference 

to radio or television reception, which can be determined by turning 

the equipment off and on, the user is encouraged to try to correct the 

interference by one or more of the following measures:

•  Reorient or relocate the receiving antenna.

•  Increase the separation between the equipment and receiver.

•  Connect the equipment into an outlet on a circuit different from 

that to which the receiver is connected.

•  Consult the dealer or an experienced radio/TV technician for help.

Note

Changes and modifications not expressly approved by the manufactu-

rer or registrant of this equipment can void your authority to operate 

this equipment under Federal Communications Commission’s rules.

Industry Canada (IC) Compliance Notice

This device complies with Industry Canada license-exempt RSSs. Ope-

ration is subject to the following two conditions: (1) this device may 

not cause interference, and (2) this device must accept any interferen-

ce, including interference that may cause undesired operation of the 

device.
Cet appareil est conforme aux normes d’exemption de licence RSS d’In-

dustry Canada. Son fonctionnement est soumis aux deux conditions 

suivantes : (1) cet appareil ne doit pas causer d’interférence et (2) cet 

appareil doit accepter toute interférence, notamment les interférences 

qui peuvent affecter son fonctionnement.

Legal Notices

All information, including, but not limited to, information regarding the 

features, functionality, and/or other product specification are subject 

to change without notice. Fibaro reserves all rights to revise or upda-

te its products, software, or documentation without any obligation to 

notify any individual or entity.

FIBARO  and Fibar Group logo are trademarks of Fibar Group S.A. All 

Содержание DOOR/WINDOW SENSOR 2

















Отзывы:

Нет отзывов