manualshive.com logo in svg

Festo IIFB9-02 Series, Руководство пользователя

Поделиться
Скачать
Festo IIFB9-02 Series Скачать руководство пользователя страница 64

The following components of the valve termi-

nal/valve sensor terminal are supplied separately
with the DC +24V operating voltage via this con-
nection:

•

electronic components and/or inputs 
(tolerance: 

±

 25%)

•

outputs 
(tolerance: 

±

 10%)

PLEASE NOTE
The electronic components and inputs have a
greater tolerance range of the 24V operating
voltage than the outputs. Under certain cir-
cumstances, this can cause the electronic

components to indicate the switching status of
the outputs, although the latter are not in the
switched position (operating voltage of the out-
puts outside the tolerance range).

The 24 V operating voltage of the outputs should
be tested whilst the system is operating. Please

ensure that the operating voltage of the outputs
is within the permitted tolerances even during full
operation.

PLEASE NOTE
Always connect the earth/ground cable to
pin 4 of the operating voltage connection.
Ensure that the valve terminal housing and the

protective earth conductor at pin 4 have the
same voltage and that no equalizing currents
flow. 
Connect a protective earth conductor with suf-

ficient cross section to the earth connection
marked with     if the valve terminal is not
fitted on earthed machine stand.

VIFB9 - 02               4. Installation

9609

4-27

Содержание IIFB9-02 Series






































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды