Festo CPV ASI-4E3A-Z Series Скачать руководство пользователя

Страница: 5 / 14

Festo

CPVASI4E3AZ

2018-11c English

Installation instructions

3.1 AS-Interface Addresses

Before connecting to the AS-Interface bus: assign an
unused address to each slave.

Address assignment

The assignment of the data bits to the inputs and outputs
of the slave shows the following figure:

IO code 7

I/O

–

Inputs:

Outputs:

Data bits:

I/O =

i directional (B)

The address mapping depends on the configuration of the
master.

3.2 Assigning the AS-Interface address

Note

Addressing valve terminal type CPV...-GE-ASI-4E3A-... is
only permitted with addressers as per specification 2.1.
Other addressers do not permit clear access to the
slaves and in some cases overwrite the ID1 code.

Recommendation: Use the Festo addresser type
ASI-PRG-ADR with adapter cable type KASI-ADR.

Содержание CPV ASI-4E3A-Z Series















Результаты поиска

Содержание CPV ASI-4E3A-Z Series

Отзывы:

Похожие инструкции для CPV ASI-4E3A-Z Series

Бренды по названию

Популярные бренды

Festo CPV ASI-4E3A-Z Series, Краткое описание

Результаты поиска

Содержание CPV ASI-4E3A-Z Series

Отзывы:

Похожие инструкции для CPV ASI-4E3A-Z Series

Бренды по названию

Популярные бренды