Festo CP-AM-MEAS Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 94

Festo CP-AM-MEAS Скачать руководство пользователя страница 8

Intended use

8

© Festo Didactic

8154245 en

2

Intended use

Festo Didactic systems and components must only be used:

•

For their intended use in teaching and training applications

•

When their safety functions are in perfect condition

The components and systems are designed in accordance with the latest technology and recognized safety
rules. However, life and limb of the user and third parties may be endangered and the components may be
impaired if they are used incorrectly.

The Festo Didactic learning system has been developed and produced exclusively for education and training
in the field of automation technology. The training company and/or trainers must ensure that all trainees
observe the safety precautions described in these operating instructions.

Training with complex machinery is a highly hazardous activity. The operating company must draw up and
document a workplace risk assessment. The trainees must be briefed on all the relevant safety aspects
before work commences.

Festo Didactic hereby excludes any and all liability for damages suffered by apprentices, the training
company and/or any third parties, which occur during use of the device in situations which serve any
purpose other than training and/or vocational education, unless such damages have been caused by
Festo Didactic due to malicious intent or gross negligence.

All extensions and accessories must be approved by Festo Didactic, and are only permitted for use for their
intended purpose.

The machine fulfils the requirements of the European directives that applied when it was commissioned. Any
modification to the machine shall render the manufacturer's CE Declaration of Conformity null and void. The
CE Declaration of Conformity must be renewed following each major modification.

«
...
6
7
8
9
10
...
»

Содержание CP-AM-MEAS































































































Отзывы:

Нет отзывов