Festo CP-AM-MEAS Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 94

background image

Basic safety instructions

12

© Festo Didactic

8154245 en

4.3

Electrical components

WARNING

•

Disconnect from all sources of electrical power!

–

Switch off the power supply before working on the circuit.

–

Please note that electrical energy may be stored in individual components.
Further information on this issue is available in the datasheets and operating
instructions included with the components.

–

Warning!

Capacitors inside the device may still be charged even after being disconnected
from all sources of voltage.

•

Danger due to malfunction

–

Never place or leave liquids (e.g. drinks) on the station in open containers.

–

The machine must not be switched on if there is condensation (moisture) on its
surface.

–

Never lay pipes/hoses designed to carry liquid media near the machine.

•

Electric shock due to connection to unsuitable power supply!

–

When devices are connected to an unsuitable power supply, exposed
components can cause dangerous electrical voltage that can lead to severe or
fatal injury.

–

Always use power supplies that provide SELV (safety extra-low voltage) or PELV
(protective extra-low voltage) output voltages for all the connections and
terminals on the electronics modules.

•

Electric shock when there is no protective grounding in place

–

If there is no protective grounding terminal in place for a Protection Class I
device, or if the protective grounding terminal has not been installed correctly,
exposed, conductive parts may carry high voltages, thus causing severe or fatal
injury if touched.

–

Ground the device in accordance with the applicable regulations.

WARNING

•

Risk of fire due to use of unsuitable power supply

–

If a device i connected to an unsuitable power supply, this can cause
components to overheat, leading to a breakout of fire.

–

Always use limited power supplies (LPSs) for all the connections and terminals
on the electronics modules.

«
...
10
11
12
13
14
...
»

Содержание CP-AM-MEAS































































































Отзывы:

Нет отзывов

Похожие инструкции для CP-AM-MEAS

Бренд: Makerfire Страницы: 10

Бренд: Sagola Страницы: 8

Бренд: DB Industries Страницы: 60

Бренд: vc999 Страницы: 55

Бренд: Salsbury Industries Страницы: 4

Бренд: NANLUX Страницы: 39

Бренд: QRS Страницы: 16

Бренд: QMAXZ Lighting Страницы: 36

Бренд: Zero88 Страницы: 26

Бренд: HAMOKI Страницы: 7

Бренд: H&S Страницы: 56

Бренд: Pani Страницы: 12

Бренд: unicraft Страницы: 16

Бренд: ABB Страницы: 13

Бренд: FASTER TOOLS Страницы: 19

Бренд: Öhlins Страницы: 8

Бренд: ?HC Страницы: 2

2261998USBA1-XX

Бренд: MMF POS Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды