Festo CP-AM-MEAS Скачать руководство пользователя страница 49

Страница: 49 / 94

Commissioning

8154245 en

7.4.3

Assembly of an CP application module to a CP Factory basic module

NOTE

The procedure for installing a CP application module on a basic module is identical for
all basic modules. The following example is an example for all basic modules and
applications.

Positioning slot nuts in the cross profiles of the CP Factory basic module

Mounting the CP application module is very easy:

•

Two M5-slot nuts (1) have to be put into the inner front slot of the cross profile (4) of the
CP Factory basic module.

•

Then put two additional M5-slot nuts (1) into the inner back slot of the cross profile (2) of the basic
module.

•

Then you have to position the slot nuts (1) approximately to the distance of the vertical cross profiles of
the CP application module.

Positioning slot nuts / illustration similar

Position

Description

slot nut

back cross profile

Inner slot (front cross profile)

front cross profile

Содержание CP-AM-MEAS































































































Результаты поиска

Содержание CP-AM-MEAS

Отзывы:

Festo CP-AM-MEAS, Оригинальная инструкция по эксплуатации, Страница: 49 / 94

Результаты поиска

Содержание CP-AM-MEAS

Отзывы: