manualshive.com logo in svg

Festo 572986, Руководство пользователя, Страница: 5 / 42

Поделиться
Скачать
Festo 572986 Скачать руководство пользователя страница 5

CMMS-AS-...-G2 – STO

Festo – GDCP-CMMS-AS-G2-S1-EN – 1306NH – English

5

Notes on this documentation

This documentation serves the purpose of safe work with the safety function STO – “Safe Torque Off ”

with use of the motor controller CMMS-AS-...-G2.

•

In addition, always observe the general safety regulations for the CMMS-AS-...-G2.

The general safety regulations for the CMMS-AS-...-G2 can be found in the hardware doc-

umentation, GDCP-CMMS-AS-G2-HW-...

Tab. 1.

Observe the information regarding safety and the requirements for product use in

chapter 1.

Product identification

This documentation refers to the following versions:

–

Motor controller CMMS-AS-...-G2 from Rev 01.

–

Motor controller CMMS-AS-...-G2 from Rev 02.

–

Firmware from FW 1.4.0.2.4.

The representation on the rating plate can be found in the hardware description,

GDCP-CMMS-AS-G2-HW-...

Service

Please consult your regional Festo contact if you have any technical problems.

Содержание 572986











































Отзывы:

Нет отзывов