background image

Not for 

Reproduction

12

ferrismowers.com

 

 

Danger - Amputation hazard:

 Do

not mow when children or others are

around. Never carry riders especially,

children even with the blades off. Do

not mow in reverse unless absolutely

necessary. Look down and behind –

before and while backing. 

 

 

Danger - Tipping and slipping

hazard:

 Operating on slopes can

be hazardous and cause a loss

of control and roll-overs. Do not

operate on slopes over 15* degrees.

Avoid sudden turns or rapid speed

changes. Reduce speed and use

extreme caution on slopes. Avoid

turning down slopes; if possible,

turn up slopes. Do not operate

down slopes towards or near water,

retaining walls, or drop-offs. Give

yourself a minimum of two mower

widths of clearance around these

hazards. 

 

 

Danger - Thrown objects

hazard:

 Keep bystanders and

children a safe distance away.

Remove objects that can be thrown

by the blade. Do not mow without

discharge chute in place. 

 

 

Danger - Thrown Objects

Hazard:

 Do not mow without

discharge chute or entire grass

catcher in place. 

 

 

Danger - Amputation and Thrown

Objects Hazard:

 To avoid injury

from rotating blades, stay clear of

deck edge and keep others away. 

 

 

Danger: Fire Hazard:

 Keep unit

free of grass, leaves and excess

oil. Do not add fuel while engine is

hot or running. Stop engine, remove

key and allow to cool for at least

3 minutes prior to adding fuel. Do

not add fuel indoors, in an enclosed

trailer, garage or other enclosed

areas. Clean up spilled fuel. Do not

smoke while operating this machine. 

*This limit was determined per International Standard ISO 5395-3:2013,

Section 4.6 and is based on the ISO 5395-3 Stability Test procedure

described in Annex A. The 15 degree “limit of stability” is equal to 60%

of the angle at which machine lift-off occurred in static tests. Actual

dynamic stability may vary depending on operating conditions.

Danger: Dismemberment - 

This

machine can crush and cut. Keep

hands away from deck lift rod.

Danger: Dismemberment - 

This

machine can crush and cut. Keep

hands away from belts and pulleys.

Warning: Avoid Serious Injury or

Death from Roll Over - 

Keep roll bar

in the raised position and use seat

belt. There is no roll over protection

when roll bar is down. Lower roll bar

only when necessary and NEVER

remove it. Raise the roll bar as soon

as clearance permits.

Warning: Avoid Serious Injury or

Death from Roll Over - 

Keep roll bar

in the raised position and use seat

belt. Do NOT use seat belt when the

roll bar is down.

Warning: Avoid Serious Injury or

Death from Roll Over - 

Do NOT

jump off if the mower tips. Read and

follow all operating instructions and

warnings in the operator’s manual.

Warning: Low Overhanging

Obstacles Hazard - 

Check for

overhead clearances before driving

under any objects. Stay clear. Do

NOT allow roll bar to contact low

overhanging obstacles, such as tree

branches and guide wires. Read and

follow all operating instructions and

warnings in the operator’s manual.

Warning: Fire Hazard - 

Keep

children, open flames and sparks

away from the battery, which could

ignite explosive gases.

Warning: Sulfuric acid can cause

blindness or severe burns - 

Always

wear safety goggles or a face shield

when working on or near a battery.

Warning: Batteries produce

explosive gases - 

Read and

understand the Operator’s Manual

before using this machine.

Important: Do not discard a

battery in the trash - 

Contact

local authorities for disposal and/or

recycling of batteries.

Safety Icons for Optional Jack Kit

Accessory

An optional jack kit is available as an accessory through your

normal parts source. Please see the explanations below for

the safety icons displayed on the jack kit. 

 

Part Number:

 5105632 - Decal, Warnings, Svc Jack 

 

1.) Warning - Read the Operator's Manual. 

 

 

2.) Crushing Hazard, Mower:

 (1.) Park machine on flat

level ground and engage the parking brake; (2.) Stop the

engine and remove the ignition key; (3.) Properly jack the

Содержание ISX800Z Series

































Отзывы: