manualshive.com logo in svg

Ferno XT, Руководство пользователя и по обслуживанию, Страница: 13 / 56

Поделиться
Скачать
Ferno XT Скачать руководство пользователя страница 13

13

© Ferno s.r.l. MU-086-G Rel.01102019

XT Extrication Device 

5.1  Before placing the device into   

 service

Staff using the extrication device must have carefully read 

and understood the information contained in this manual. 

● 

Before performing any operation with the extrication 

device, make sure that: the Quick Head Immobilizer, 

the triangular head immobiliser and the chin strap 

have been correctly applied and are ready for use; the 

restraints have been correctly applied according to 

their number (two upper chest restraints and two lower 

groin restraints).

● 

Ensure that the device does not show any signs of 

damage or wear, and that it is fully operational. Refer 

to section

 8.5 Inspection

, page 44.

5.2  Instructions for Use

● 

This manual does not provide any medical instructions.

● 

It is the responsibility of the operators to follow correct 

procedures and ensure the safety of both the patient 

and themselves. 

● 

This manual explains the use of the extrication device 

under ideal conditions and is purely indicative. 

● 

The use of the device requires a minimum of two 

trained and qualified operators.

● 

These operators must work together and coordinate 

correctly during all operations.

● 

Follow procedures while complying with standard 

regulations for moving the patient in an emergency.

● 

Lift only the weight that you can safely support. 

Obtain additional assistance for heavy loads.

● 

The extrication device can be adapted to a variety of 

circumstances and different scenarios. The trained 

staff of the emergency service must assess the patient's 

conditions and determine the most suitable equipment 

and procedures.

● 

In any case, always observe local healthcare 

instructions and regulations.

● 

Always assist the patient and never leave them alone 

during the operations with the device. 

Use of the extrication device

 

WARNING

Never leave the patient alone while tied to the 

extrication device. Assist the patient throughout all 

rescue operations.

Important

When the extrication device is not used, store it indoors 

in a dry place. It is recommended to use its carry bag 

for storage purposes.

5 - USE OF THE EXTRICATION DEVICE

 

WARNING

The use of improper and/or unauthorised devices 

may cause accidents, damage, and/or injury. 

Use only devices that have been approved and 

authorised by Ferno S.R.L. 

Read the user 

manual carefully

At least two 

qualified 

operators

2

Load capacity

 

160 kg 

352 lb

Содержание XT

























































Отзывы:

Нет отзывов