Ferno 0731305 Скачать руководство пользователя страница 42

Страница: 42 / 47

Maintenance

9.12 Calibrating the Paddles

kNOWiNG WhEN CaLibRaTiON iS NEEDED

The paddles are pressure-sensitive. When properly calibrated,

the paddles allow the operator to control the speed of the belts.

Applying less pressure should make the belts move slowly, while

depressing the paddle fully should make the belts move as quickly

as possible.
Recalibration of the paddles is needed when you observe any of

the following:

●

there is no difference between a light touch of the paddle and

fully-depressing the switch (the belts should not immediately

begin moving at full speed with only light pressure)

●

if the belts continues to move when the switch has been

released (no pressure)

CaLibRaTiNG ThE PaDDLES

1. If needed, disconnect the interconnect cord. Press the power

switch

. Wait until the lights on the control panel turn off

and the control panel is inactive (about five seconds).

Note:

The calibration procedure cannot begin unless the

interconnect cord is disconnected, the power is OFF, and the

control panel is inactive.

Do not

touch the up/down paddles.

3. Simultaneously press the brake

and mode

buttons

on the control panel (Figure 66).

Note:

If Step 3 is completed properly, the control panel will

illuminate with a red background. The software version is briefly

shown, then the calibration sequence begins. If the background is

not red and the standard screen is displayed, repeat Steps 1-3.

4. Instruction: “Throttle UP 100% Then Press a Key”: Press

and hold the ASCEND part of the paddle fully, then press the

mode or brake button.

5. Instruction: “Throttle DW 100% Then Press a Key”: Press

and hold the DESCEND part of the paddle fully, then press

the mode or brake button.

6. Instruction: “Throttle IDLE 0% Then Press a Key”: Leave

the paddle in the neutral position and press the mode or brake

button.

7. If you completed all steps properly, the display will show

“Calibration OK!” Begin using the chair normally.

iF ThE CaLibRaTiON FaiLS

Repeat Steps 1-7. Do not press the paddles until directed to, and

press in the proper direction. If the paddles cannot be recalibrated,

contact Ferno Technical Support for assistance (page 2).

Paddle Calibration

The paddles cannot be re-calibrated when the

interconnect cord is connected. Disconnect

the interconnect cord and install fresh “AA”

batteries in the control panel if needed.

Содержание 0731305
















































Результаты поиска

Содержание 0731305

Отзывы:

Похожие инструкции для 0731305

Бренды по названию

Популярные бренды

Ferno 0731305, Руководство пользователя

Результаты поиска

Содержание 0731305

Отзывы:

Похожие инструкции для 0731305

Бренды по названию

Популярные бренды