Ferm
39
SYMBOLFORKLARING
I denne brugervejledninge og/eller på maskinen anvendes der følgende piktogrammer:
I overensstemmelse med grundlæggende sikkerhedsstandarder i de europæiske
direktiver.
Klasse II maskine – Dobbelt isolering – Du behøver ingen jordforbindelsestik.
Betegnelse for risiko for personskader, dødsfald eller beskadigelse af værktøjet i
tilfælde af at du er uopmærksom på instruktioner i denne manual.
indikerer farer for elektrisk stød
Defekte og/eller kasserede elektriske eller elektroniske maskiner skal afleveres på en
genbrugsplads.
Variabel hastighedsregulering
Tag straks stikket ud af stikkontakten, hvis ledningen beskadiges og i forbindelse med
vedligeholdelse
Anvend altid høreværn.
Lydeffektniveau
• Værktøjet bør ikke betjenes i fugtige og våde omgivelser; ved regn, tåge eller sne i det fri, og
i omgivelser med eksplosionsfare.
• Kontakten bør være i “OFF” position før stikket sættes i hovedkontakten.
• Hvis du har langt hår, bør du bære hårbeskyttelse. Arbejd kun med tætsiddende tøj.
• Sikre beholderen med blandingsindholdet sådan at den ikke rykkes på gulvet.
• Led altid ledningssnoren bagover væk fra værktøjet. Ledningssnoren bør ikke udsættes
for stræk og bør ikke ligge på eller ligge over skarpe kanter.
• Anvend det ekstra håndtag.
• Hold øje med at ledningen ikke bliver snoet.
• Bær høreværn og øjenbeskyttelse.
2. SIKKERHEDSINSTRUKTIONER
DK
06
Ferm
The necessary speed depends on the type of the material mixed and it is recommended to
verify it by a practical test.
Constant electronics
The constant electronics keeps the speed between no-load and load nearly constant and
ensures uniform mixing of the materials.
Electronic overload protection
In case that the machine is extremely overloaded, an electronic overload protection protects
the motor from damage. In this case, the motor stops and restarts only after the feeding
pressure is reduced.
Temperature-dependant overload protection
To protect the motor from overheating at extreme permanent load, it is switched off by the
protective electronic system when a critical temperature is reached.
After a cooling-down period of approx. 3 - 5 min., de machine is again ready for use and can be
fully loaded.
When the machine is warmed by use, the temperature-dependent overload protection reacts
earlier as a result.
Maintenance
Make sure that the plug is removed from the mains when carrying out maintenance work on
the motor. The Ferm machines have been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation depends upon proper machine
care and regular cleaning.
- The ventilating slots on the motor casing should be cleaned out from time to time.
- When the carbon brushes are worn out, the machine switches itself off. The machine must
then be sent to customer service for maintenance.
- After 100 hours: check carbon brushes
- After 200 hours: renew the grease filling in the gearbox
To verify the protective insulation remains intact, the machine must be subjected to a
technical safety test afterwards. For this reason, this maintenance must be
performed exclusively by a professional electro-workshop.
Cleaning
Regularly clean the machine housing with a soft cloth, preferably after each use. Keep the
ventilation slots free from dust and dirt. If the dirt does not come off use a soft cloth moistened
with soapy water. Never use solvents such as petrol, alcohol, ammonia water, etc. These
solvents may damage the plastic parts.
Faults
Should a fault occur, e.g. after wear of a part, please contact the service address on the
warranty card. In the back of this manual you find an exploded view showing the parts that can
be ordered.
6. SERVICE & MAINTENANCE
UK
