Ferm
35
AVAILABLE SPARE PARTS FOR BS-702
REF.NR.
DESCRIPTION
FERM NR. BS-702
4
BALL BEARING 6201 ZZ
806201
5
DRIVE ROLLER
402800
12
ADJUSTMENT BOLT
402801
14
IDLER ROLLER
402802
17
PLATE TABLE
402803
21
DRIVE PULLEY
402804
23
MOTOR
402805
27
BASE PLATE
402806
28
SWITCH
402807
30
BAR
402809
31
ADJUSTMENT BLOCK
402810
32
MOTOR PULLEY
402811
33
V-BELT M21
402812
36
ALUMINIUM DISC
402815
39
TABLE BRACKET
402816
40
TABLE TILT TRUNION
402817
41
MITRE BAR
402818
42
KNOB/BOLT FOR MITRE BAR
402819
46
TABLE
402820
47
MITRE GAUGE
402821
49
SHAFT FOR DRIVE ROLLER
402822
51
SHAFT FOR IDLER ROLLER
402823
52
BALL BEARING 6201 ZZ
806201
56
INDICATOR
402824
78
CAPACITOR (6 µF = 450 VAC)
402825
77 RUBBER FOOT
402826
2
Ferm
Product:
Ferm Belt sander
Type
BS-702
, Article number
330702
Ferm, Genemuiden, The Netherlands
Sound pressure level Lpa
80 dB(A)
SERIAL NUMBER
The serial number on the machine consists of the fol-
lowing elements.
Serial nr.
READ THIS MANUAL CAREFULLY BEFORE USING
THE BELT SANDER!
1. SPECIFIC SAFETY RULES
BEFORE USING THE MACHINE:
1. The following points need to be checked:
- Do the connecting voltage of the machine corre-
spond with the mains voltage;
- Are the mains lead and the mains plug in a good
condition; strong, without ravels or damages.
2. For functional reasons the turning parts of this machi-
ne are not covered. Therefore it is of utmost impor-
tance to be careful. Hold the workpiece firmly, to
prevent it from slipping from your hands. Never
touch the sanding surfaces of a working machine with
your hands.
3. Avoid the use of long extension cables.
4. If necessary, secure the sanding machine with screws.
BEFORE YOU OPERATE THE MACHINE:
1. Always keep the mains cable away from moving parts
of the machine;
2. Use safety goggles;
3. Use a dust mask.
IMMEDIATELY SWITCH OF THE MACHINE
IN CASE OF:
1. defective mains plug, mains line or damage to the
mains line;
2. defective switch;
3. smoke or bad smell caused by scorched isulation.
2. INSTALLATION
Avoid the use of long extension cables. If necessary, secu-
re the sanding machine on a working bench with help of
screws through the holes in the feet of the machine fra-
me. Do not forget to leave enough space around the ma-
chine for the workpieces to be sanded.
3. DESCRIPTION
This machine combines all the advantages of a horizontal
and a vertical belt sander with those of a disc sander. Its
sturdy construction in cast iron and steel makes the ma-
chine suitable for every sanding job.
4. BEFORE PUTTING THE MACHINE
INTO OPERATION
OPERATION (SEE FIG. 1)
1. Machine frame;
2. Motor;
3. Roller stop and parallel stop;
4. Clamping handle;
5. Transport roller;
6. Sanding belt;
8. Fence;
9. Drive roller;
10. Aluminium disc;
11. Sanding disc;
12. Work plate;
13. Mitre scale;
14. Supporting arm.
ASSEMBLY
-
Put the machine frame on its head and press the four
rubber stops into the foot of the frame.
-
Machine frame, aluminium disc (10) and work plate
(12) are supplied in separate packaging.
-
Push the aluminium disc on the shaft and fasten the
ORDER NUMBER/YEAR OF CONSTRUCTION
GB
English
230 V~
50 Hz
375 W
1'
;
n
0
= 1450/min (disc)
V
0
= 275 m/min (belt)
1'
150 mm
100 x 915 mm
