6
M
M
M
M
H
H
H
H
-
-
-
-
5
5
5
5
0
0
0
0
0
0
0
0
M
M
M
M
e
e
e
e
tt
tt
a
a
a
a
ll
ll
h
h
h
h
e
e
e
e
a
a
a
a
d
d
d
d
™
™
™
™
C
C
C
C
o
o
o
o
n
n
n
n
tt
tt
r
r
r
r
o
o
o
o
ll
ll
s
s
s
s
A. INPUT - Plug your guitar in here.
B. CLEAN/DIRTY SELECT - Press to switch between
CLEAN and DIRTY channels as shown by the LEDs:
green—CLEAN channel
yellow or
red—“DIRTY” (Drive) channels
C. DRIVE SELECT - Press DRIVE SELECT to switch
between TIGHT DRIVE and LOOSE DRIVE channels
(as shown by the LEDs when CLEAN / DIRTY
SELECT {B} is set to “DIRTY”):
yellow—TIGHT DRIVE channel
red—LOOSE DRIVE channel
NOTE:
When CLEAN / DIRTY SELECT {B} is set to
“CLEAN,” use DRIVE SELECT to “pre-select” a DIRTY
channel as shown by the color of the footswitch LED.
D. DRIVE - Use these knobs to adjust the distortion level
of each DIRTY channel.
E. VOLUME - Use these knobs to adjust the loudness of
each channel.
F.
PRESENCE - Use these knobs to adjust the ultra-high
frequency response of each DIRTY channel.
G. TREBLE / MID / BASS - Use these knobs to adjust
the high–, middle–, and low–frequency response (EQ)
of each channel.
H. BOOST - Use this knob to set a volume boost level for
all channels; useful for lead solos. Use the footswitch
to switch BOOST on–off.
I.
FX LEVEL - Use this knob to adjust the level of the
selected effect. Use the footswitch to switch the
onboard effects on–off.
J.
FX SELECT - Use this knob to select one of the 16
effects described on the next page.
K. POWER - Press this switch to turn the amplifier on-off
as indicated by the LED.
NOTE:
Turn down all 3
VOLUME knobs before switching the MH-500 on!
Rear Panel
N. POWER INPUT - Connect the included power cord to
a grounded AC outlet in accordance with the voltage
and frequency ratings specified on the rear panel of
your amplifier.
O. SPEAKER OUTPUTS - Only connect speakers with a
total impedance load equal to the
SPEAKER SELECT
setting for optimal gain performance:
4
Ω
—Two 8
Ω
speakers or one 4
Ω
speaker
2
Ω
—Four 8
Ω
speakers or two 4
Ω
speakers
P.
XLR LINE OUT - Balanced connection for speaker-
emulated output to a mixing console. Use
LINE OUT
LEVEL
to adjust the signal output level. Use
GROUND/LIFT
to disconnect the ground connection
(pin-1) to reduce “ground loop” noise caused by non-
standard wiring.
GROUNDED (normal)
GROUND LIFTED
Q. FOOTSWITCH - Plug the included footswitch in here.
The footswitch disables channel selection from the
front panel switches {B,C}.
One of the most powerful electric guitar amplification
systems known to man…The MH-500 Metalhead™!
•
550 Watts into 2 Ohms (a pair of MH-412 enclosures)
•
400 Watts into 4 Ohms (a single MH-412 enclosure)
•
Forced-Air fan cooling
•
Three-Channel preamp voiced for the new millennium
•
•
CLEAN—studio-pure, with tons of headroom
•
•
TIGHT DRIVE—covers the palette of vicious Rock
guitar tones
•
•
LOOSE DRIVE—combines copious distortion with
high-headroom, uncontrolled power-amp rumble
for modern drop-tuned Metal, Punk, and…beyond
•
•
BOOST—footswitchable boost on any channel,
effectively providing SIX channel performance
•
Digital Reverb and effects including new GATE feature
•
Professional speaker-emulated XLR Line Out with
Level control & Ground Lift
✧
f
f e
e n
n d
d e
e r
r .
. c
c o
o m
m
✧
Содержание Metalhead 500
Страница 1: ......
Страница 18: ...18 f f e e n n d d e e r r c c o o m m...
Страница 19: ...19 f f e e n n d d e e r r c c o o m m...
