background image

User’s Manual S40-T

FEMA ELECTRÓNICA - Page 10

Relay type 

3 contacts (Com, NC, NO)

Maximum current 

8A (resistive load)

Voltage 

250 Vac continuously

Instalable in 

Option1 and/or Option2

A  B  C  D  E

Common

NC

NO

K  L  M  N

F  G  H  I  J

Common

NC

NO

O  P  Q  R

Connections for Option1

Connections for Option2

Manufacturer  FEMA ELECTRÓNICA, S.A.

 

Altimira 14 - Pol. Ind. Santiga

 

E08210 - Barberà del Vallès

 

BARCELONA - SPAIN 

 

www.fema.es - [email protected]

Products -   S40-T

The manufacturer declares that the instruments indicated 

comply with the directives and rules indicated below.

Directive of electromagnetic compatibility 2004/108/CEE

Directive of low voltage 73/23/CEE

Security rules 61010-1

Equipment “Fixed” 

 

“Permanently connected”

Pollution degree 1 and 2 (without condensation) 

Isolation Double

Emission rules

61000-6-4   Generic rule of emission

Immunity rules

61000-6-2 

Generic rules of immunity

61000-4-2 

By contact ±4KV - Criteria B

 

On air ±8KV - Criteria B

61000-4-3  

Criteria A

61000-4-4   On AC power lines: ±2KV - Criteria B

 

On DC power lines: ±2KV - Criteria B

 

On signal lines : ±1KV - Criteria B

61000-4-5 

Between AC power lines ±1KV - Criteria B 

 

Between DC power lines ±0.5KV - Criteria B

61000-4-6 

Criteria A

61000-4-8 

30A/m at 50Hz - Criteria A

61000-4-11  0% 1 cycle Criteria A

 

40% 10 cycle Criteria B

 

70% 25 cycle Criteria B

 

0% 250 cycle Criteria B

Barberà del Vallès November 2011

Daniel Juncà - Quality Manager

All instruments are warranted against all manufacturing 

defects for a period of 24 MONTHS from the shipment date. 

This warranty does not apply in case of misuse, accident or 

manipulation by non-authorized personnel. In case of mal-

function get in contact with your local provider to arrange for 

repair. Within the warranty period and after examination by 

the manufacturer, the unit will be repaired or substituted when 

found to be defective. The scope of this warranty is limited to 

the repair cost of the instrument, not being the manufacturer 

eligible for responsibility on additional damages or costs. .

You may need to access the inside of the instrument to insert 

additional options. Use a flat screwdriver to unlock the upper 

clips marked with “A”. Then unlock the lower clips marked 

with “B” and move out the front filter. Let the inside of the 

instrument slide out of the housing.

To reinsert the instrument make sure that all modules are 

correctly connected to the pins on the display module. Place 

all the set into the housing, assuring that the modules cor-

rectly fit into the internal guiding slides of the housing. Once 

introduced,  place  again  the  front  filter  by  clipping  first  the 

upper clips “A” and then the lower clips “B”.

Important - If your instrument was delivered with the IP65 front 

seal option, accessing the inside of the instrument will perma-

nently break the IP65 seal on the areas of clips “A” and “B”.

A

B

Option R1 - 1 relay

Warranty

CE Declaration of Conformity

Accessing the instrument

Содержание S40-T













Отзывы: