Fema S40-C1, Руководство пользователя, Страница: 14 / 28

FEMA ELECTRÓNICA . Series S . S40-C1
14
1.19 Configuration menu (cont.)
The ‘ On Power Up ’ (‘ on.Pu ’) menu configures functions to apply at
start-up. It applies only to instrument restart after power loss. It does
not apply to instrument restart due to change in configuration.
• parameter ‘ Delay ’ (‘ dLAy ’) assigns a waiting time in seconds. The
instrument waits the configured time before starting normal func -
tion. During this waiting time, the display shows all decimal points
on in flash mode, all alarms are in ‘oFF’ state, there is no signal acqui -
sition and there is no communications or control being performed.
After the configured time is over, the instrument starts in normal
function. Delay value between 0 and 200 seconds.
• the ‘
Reset ’ (‘ rSt ’) parameter will execute a reset of the counter
each time the instrument is restarted.
1.19.15 Menu ‘On Power Up’
Tools
Key UP
(‘fast access’)
Memory of
maximum
Memory of
minimum
Setpoint 1
Setpoint 2
Memory of
cycles
Preset value
On power-up Delay Seconds
Reset
The ‘UP’ (
5
) key at the front of the instrument gives access to a list of func -
tions configurable by the operator. See section
1.17
for an explanation on how
to operate the ‘
fast access
’ menu.
The ‘ Key UP (Fast access) ’ (‘ K.uP ’) menu allows to select which functions will
be accessible through the ‘fast access’ menu. Select ‘ on ’ to activate each func -
tion.
• the ‘
Setpoint 1 ’ (‘ ALr1 ’) function allows to visualize and modify the alarm 1
setpoint through the ‘fast access’ menu.
• the ‘
Setpoint 2 ’ (‘ ALr2 ’) function allows to visualize and modify the alarm 2
setpoint through the ‘fast access’ menu.
• the ‘
Memory of maximum ’ (‘ MAX ’) or ‘ Memory of minimum ’ (‘ MIn ’) func -
tions allow to visualize the maximum or minimum reading value stored in
memory. To reset this value, visualize the memory value at the ‘fast access’
menu with key UP (
5
) and when message ‘ rSt ’ is displayed, press (
<
) to re -
set.
• the ‘ Memory of cycles ’ (‘ cYcL ’) function allow to visualize and reset the
memory of cycles. To reset this value, visualize the memory value at the ‘fast
access’ menu with key UP (
5
) and when message ‘ rSt ’ is displayed, press (
<
)
to reset. The memory of cycles countes ‘+1’ each time a reset alarm occurs
(‘on_AL’ / ‘to_0’ or ‘to_P’) or a reset by ‘overrange’ / ‘underrange’ occurs.
• the ‘
Preset value ’ (‘ PrSt ’) function allows to visualize and modify the preset
value configured.
1.19.12 Fast access
If only a single function is selected for the ‘fast access’ menu, press -
ing the the ‘UP’ (
5
) key will shortly display the function name and
then automatically jump to the function value.
1.19.13 Super fast access
The ‘LE’ (
3
) key at the front of the instrument can be configured to
activate several functions. Only one function can be assigned to the
‘LE’ (
3
) key
• the ‘ No function ’ (‘ nonE ’) value assigns no function.
• the ‘ Front reset ’ (‘ F.rSt ’) value assigns the reset function.
• the ‘ Alarm unlock ’ (‘ A.Lck ’) value assigns the manual unlock of the
alarms function, for instruments with the ‘ Locked alarms ’ (‘ A.Lck ’)
function activated (see section 1.19.11)
• the ‘ Reset and alarm unlock ’ (‘ Fr.AL ’) assigns the two previous
functions to the same button.
1.19.14 Menu ‘Key LE’
Key LE
Front reset
Alarm unlock
No function
Reset and alarm unlock