Fellowes Powershred C-320 Скачать руководство пользователя страница 31

Страница: 31 / 36

Revised 06/09

C-320/C-320C and C-380/C-380C Technical Service Manual

DO THIS FIRST

Remove Housing

Cover

TOOLS

Phillips screwdriver

Long nose pliers

Housing Cover

cable connects

operator panel

board to the

PC board

operator panel

Remove/Replace Operator Panel Board

The PC board on the operator panel controls the auto start LEDs, the
operator panel switches, and the indicator LEDs and ready light. The

operator panel board connects via a large cable to the PC board.

To replace the operator panel board:

Remove the 4 screws that hold the 2 cable guide brackets to the

housing cover.

Remove the 2 screws that hold the supports for the auto start LEDs.

Note the color of each lamp. Remove the sensor wires from the wire
guides.

Remove the 2 screws that hold the operator panel board to the

cover.

Disconnect the operator panel switch cable from the operator panel

board.

Connect the operator panel switch cable to the new operator panel

board.

Put the new board in position and replace the 2 screws that hold the

board to the cover.

Put the auto start LEDs in the openings along the paper entry slot

and replace the LED support. Put the wires in the wire guides.

Put the large cable in the cable guides and replace the cable guide

brackets.

Replace Operator Panel Swtches

The operator panel switches (Reverse, Off, Automatic, and Manual Forward)

are located in the housing cover insert and connect via a cable to the

operator panel PC board. If the cable or a switch is defective, replace the

housing cover insert.

To replace the housing cover insert:

Remove the 8 screws that hold the cover insert to the cover.

Lift the insert up and away from the cover.

Put the new insert in place and secure it to the housing cover.

Connect the operator panel switch cable to the operator panel

board.

Содержание Powershred C-320





































Результаты поиска

Содержание Powershred C-320

Отзывы:

Похожие инструкции для Powershred C-320

Бренды по названию

Популярные бренды

Fellowes Powershred C-320, Техническое и сервисное руководство

Результаты поиска

Содержание Powershred C-320

Отзывы:

Похожие инструкции для Powershred C-320

Бренды по названию

Популярные бренды