Fellowes Powershred C-320 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 36

background image

Revised 06/09

C-320/C-320C and C-380/C-380C Technical Service Manual

Remove/Replace PC Board

The PC board is located at the right side of the cabinet shelf. It rests on a
support base that is attached to the cabinet shelf. Some of the wires leading to

various components are hard-wired to the board, others such as the basket full
sensor and the operator panel cable, can be disconnected from the board or the

component.

If a component that is hard wired to the board fails, the entire PC board must be
replaced. Before replacing the PC board, disconnect the wires (that are not hard-
wired) from the PC board, components, and sensors.

Note: Make sure the shredder is unplugged from the electrical outlet.

1

Disconnect the 2 power wires (red and black) from the disconnect

switch (see wiring diagram).

2

Disconnect the 3 motor wires from the PC board.

3

Disconnect the black and blue wire tabs from the capacitor and remove

them from the wire guides.

4

Disconnect the basket full sensor wire connector from the PC board.

5

Remove the 4 screws that hold the PC board to the cabinet shelf, and

remove the PC board.

6

Set the PC board aside. Be careful as some of the wires are hard wired

to the PC board. Do not break these connections if the board is not
being replaced.

DO THIS FIRST

Remove Housing

Cover

TOOLS

Long nose pliers

Phillips screwdriver

operator panel

cable connector

capacitor connectors

(hardwired)

motor wire

connectors

basket full sensor

connectors

C-320/C-320C PC board

door ajar switch connectors

(hardwired)

power cord connectors

current limit

adjustment screw

«
...
21
22
23
24
25
...
»

Содержание Powershred C-320





































Отзывы:

Нет отзывов

Похожие инструкции для Powershred C-320

Бренд: IDEAL Страницы: 28

Бренд: Titanium Страницы: 76

Бренд: ABC Office Страницы: 18

Бренд: ALDI Страницы: 23

ShredMaster Jam Free GSS167

Бренд: GBC Страницы: 10

Бренд: 3devo Страницы: 33

Бренд: HSM Страницы: 160

Бренд: David-Link Страницы: 2

Powershred 11C-H

Бренд: Fellowes Страницы: 8

Бренд: Gear Head Страницы: 9

POWERSHRED 99Ms

Бренд: Fellowes Страницы: 44

AutoMax AutoMax 200C

Бренд: Fellowes Страницы: 84

Бренд: GMC Страницы: 4

Бренд: NANO MACHINES Страницы: 40

Бренд: texet Страницы: 4

Бренд: texet Страницы: 4

JUNIOR TOMAHAWK

Бренд: Troy-Bilt Страницы: 24

Бренд: Mac allister Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды