background image

Guilin Feiyu Electronic Technology Co., Ltd

 

Guilin Feiyu Electronic Technology Co., Ltd            http://www.feiyudz.cn            E-mail: [email protected]              Page 9

 

8.

 

RC receiver connection: 

RC receiver and DoS connection wires is included in the DoS product. 

Attention: the 

wires is arranged by the colors.

 

 

a) DoS requires a minimum of 6-channel RC receiver. 
b) 4 Receiver channels are used for aileron (channel 1), elevator (channel 2) 

throttle 

(channel 3) and rudder (channel 4) signal output. Connect these 4 receiver output 
signals to the DoS with the supplied wires (pay attention to the color of each channel ).   

c)  a  free  Receiver  channels  are  required  to  control  the  DoS  Flight  Modes  (a  3-position 

switch ,”SW1”). 

d)the  other  3-position  switch(SW2)  is  not  used  in  firmware  V2.0,so  you  do  not  need  to 

connect. 

 

Wire color 

Receive channel 

White   

(bundled with red 

& black) 

aileron 

Channel 

orange 

elevator 

Channel 

green 

throttle 

Channel 

yellow 

rudder 

Channel 

brown 

SW 1 

Any free channel 

controlled by   

A 3-way switch or dial 

knob 

Channel 

blue 

SW 2(not used) 

Any free channel 

controlled by   

A 3-way switch or dial knob 

Channel 

 

Attention:RC mode Setting of your controller has to be fixed wing model, and every 

channels’ maximum and minimum value to be the default value (100%), all the sticks trim 
to 0

,

 also cancel all the curve set . 

9.

 

Motor start-up instruction: 

Start Motor

When using multi-rotor firmware, pushing throttle stick before takeoff will 

Содержание DoS

















Отзывы: