background image

Guilin Feiyu Electronic Technology Co., Ltd

 

Guilin Feiyu Electronic Technology Co., Ltd            http://www.feiyudz.cn            E-mail: [email protected]              Page 1

 

                       

FY-DoS for multi-rotors control manual 

Installation & Operation        Multi-rotor firmware above V2.10

 

 
 

Dear Customer: 

Thank  you  for  choosing  DoS  as  your  autopilot  system.  Please  read  this  manual 

carefully before using the system to ensure proper use and operation. 

The  installation  and  use  of  this  device  require  some  skill  and  knowledge  in  flying 

remote controlled airplane model.   

 

If  you  are  a  complete  beginner  and  have  never  flown  one  before,  we  do  not 

recommend you install this device on your own.   

 

Please  find  assistance  from  an  experienced  RC  pilot  who  may  provide  you  with  the 

basic knowledge required to use this device successfully.   

 

If  you  are  already  an  experienced  flyer,  you  will  find the  DoS  installation  to be  easy 

and logical. Just follow this manual and you won’t go wrong. 

If you need any technical support you can send e-mail directly to:

 [email protected]

 

 

DoS module   

DoS is an Attitude Flight Stabilization System (AFSS) and autopilot system.Now can 

be used for automated stabilization of fixed wing aircrafts,and after upgrade firmware can 
be used for other aircraft and equipment control (For more details of DoS,please refer to 
the latest firmware and the instructions).

 

DoS has integrated three-axis gyro ,three-axis accelerometer,three axis magnetometer 

and  barometric  pressure  sensor.  DoS  can  accurately  measure  flight  attitude,  the  earth 
azimuth  and  through  the  barometer  to  measure  relative  altitude. 

This  manual  mainly 

introduces DoS firmware for Multi-rotor flight system. 

The  firmware  for  Multi-rotor  flight  system  above  V2.10  can  realize  the  following 

functions:( We will continue  updating new firmware to improve performance and update 
functions, please pay attention to the latest news FeiYu official website (www.feiyudz.cn) 
posted.) 

 

Attitude Stabilized Mode 

Dos  can  auto  stabilize  the  aircraft  flight  attitude  in  this  mode,  pitch  and  roll  stick 

center position for 0 °attitude,its endpoint is 45 ° , pitch and roll stick can linear control the 
flight attitude, maximum angular velocity is 150 ° / s. Yaw stick in the center position will 
lock current course , its endpoint corresponding maximum rotation rate 135 ° per second, 
yaw stick can linear control  the aircraft rotation rate. Throttle stick direct control aircraft 
climb and decline, climbing and declining rate is directly related to the throttle.   

 

Hovering Mode 

The  GPS  Module  must  be  connected  to  the  DoS  with  at  least  5  GPS  satellites 

detected.In  this  Mode,  pitch,  roll,  yaw  control  method  is  the  same  as  Attitude  Stabilized 
Mode.DOS can auto control flight altitude.Climbing and descending rate is directly related 
to the throttle, when the throttle stick is in the center position,DOS auto locks the altitude, 
in maximum means climb rate is 3 m/s, in minimum means decline rate is 1.5 m/s.Throttle 
stick  can  linear  control  the  aircraft  climb  and  decline  rate.Pitch,  roll  sticks  released  will 
lock  the  position  when  GPS  signal  is  adequate,non-released  will  equivalent  of  Attitude 
Stabilized Mode. 

Feiyu Tech 

Содержание DoS

















Отзывы: