manualshive.com logo in svg
background image

OBID i-scan

®

Manual

Communication FU

FEIG ELECTRONIC GmbH

Page 2 of 27

H30701-3e-ID-B

Note

©

 Copyright 2003-2005 by

FEIG ELECTRONIC GmbH
Lange Strasse 4
D-35781 Weilburg-Waldhausen
Tel.: +49 6471 3109-0

http://www.feig.de

With the edition of this document, all previous editions become void. Indications made in this manual may be

changed without previous notice.

Copying of this document, and giving it to others and the use or communication of the contents thereof are

forbidden without express authority. Offenders are liable to the payment of damages. All rights are reserved

in the event of the grant of a patent or the registration of a utility model or design.

Composition of the information in this document has been done to the best of our knowledge. FEIG

ELECTRONIC GmbH does not guarantee the correctness and completeness of the details given in this

manual and may not be held liable for damages ensuing from incorrect or incomplete information. Since,

despite all our efforts, errors may not be completely avoided, we are always grateful for your useful tips.

The instructions given in this manual are based on advantageous boundary conditions. FEIG ELECTRONIC

GmbH does not give any guarantee promise for perfect function in cross environments.

FEIG ELECTRONIC GmbH assumes no responsibility for the use of any information contained in this

document and makes no representation that they free of patent infringement. FEIG ELECTRONIC GmbH

does not convey any license under its patent rights nor the rights of others.

OBID i-scan

® 

is registered trademark of FEIG ELECTRONIC GmbH.

General information's regarding this document

 

If bits within one byte are filled with  "-", these bit spaces are reserved for future extensions or
for internal testing- and manufacturing-functions. These bit spaces must not be changed, as this
may cause faulty operation of the reader.

 

The following figure formats are used:
0...9:

for decimal figures

0x00...0xFF:

for hexadecimal figures,

b0...1

for binary figures.

 

The hexadecimal value in brackets "[ ]" marks a control byte (command).

Содержание OBID i-scan ID ISC.ANT.MUX




























Отзывы: