Feider Machines FSO20254, Инструкция по эксплуатации

Страница: 17 / 26

ORIGINAL INSTRUCTIONS
17
Checking the moving saw blade guard safety advice
The saw blade guard protects against accidental contact with the saw blade and from chips flying
around.
Check function
To do so, fold the saw downwards:
• The saw blade guard must provide free access to the saw blade without touching other parts.
• When folding the saw upwards into the starting position, the saw blade guard must cover the saw
blade automatically
Attachment and operation
Attaching the crosscut, drag and mitre saw
• In order to adjust the rotary table (17), loosen the handle (34) approximately 2 turns and pull up the
latched position lever (21) with your index finger.
• Turn the rotary table (17) and pointer to the desired angle measurement on the scale (18) and use the
handle (34) to secure it.
• Press the machine head (6) lightly downwards and pull the locking bolt (3) from the motor bracket at
the same time disengages the saw from the lowest position.
• Swing the machine head (6) up.
• It is possible to secure the clamping devices (7) to the left or right on the fixed saw table (15). Insert
the clamping devices (7) in the holes on the rear side of the stop rail (35) and secure it with the star
grip screws (8). For 0°- 45°mitre cuts, the clamping device (7) must only be mounted on the right side.
• It is possible to tilt the machine head (6) a max. 45° to the left by loosening the set screw(13).
• Workpiece supports (32) must always be secured and used during work. Set the desired table size by
loosening the set screw (a). Then tighten the set screw (a) again.
Precision adjustment of the stop for crosscut 90°
• No stop angle included.
• Lower the machine head (6) and secure it using the locking bolt (3).
• Loosen the set screw (213).
• Position the angle stop between the saw blade and the rotary table (17).
• Loosen the lock nut (30).
• Adjust the adjusting screw (29) until the angle between the saw blade and rotary table (17) is90°.
• Re-tighten the lock nut (30).
• Subsequently check the position of the angle indicator. If necessary loosen the pointer using a Philips
screwdriver, set to position 0° on the angle scale (14) and re-tighten the retaining screw.
Crosscut 90° and turntable 0°
In the case of cutting widths up to approx. 100 mm it is possible to fix the traction function of the saw
with the set screw (25) in the rear position. In this position the machine can be operated in cross cutting
mode. If the cutting width is over 100 mm then it is necessary to ensure that the set screw (25) is loose
and the machine head (6) can move. Attention! For 90° crosscuts, the moveable stop rail (35) must be
fixed in the inner position.
• Open the set screw (8) for the moveable stop rail (35) and push the moveable stop rail (35)inwards.
• The moveable stop rail (35) must be locked in a position far enough from the inner position that the
distance between the stop rail (35) and the saw blade is no more than 8 mm..
• Before making the cut, check that the stop rail (35) and the saw blade cannotcollide.
• Re-tighten the set screw (8).
• Move the machine head (6) to its upper position.
• Use the handle (4) to push back the machine head (6) and fxit in this position if required (dependent
on the cutting width).
• Place the piece of wood to be cut at the stop rail (35) and on the turntable (17).
• Lock the material with the clamping devices (7) on the fixed saw table (15) to prevent the material
from moving during the cutting operation.
• Release the lock switch (10) and press the ON/OFF switch (20) to start the motor.