FeelElec FY8300 Series Скачать руководство пользователя

Страница: 41 / 47

FeelElec

FY8300 Series User

’

s Manual

Uplink

FY8300 supports multi-machine uplink, which can provide users more

channels for output. In uplink network, only one master machine can exist. Others
must be set as slave machine. The setting method is as follows:

⚫

elect on FY8300 as master machine. Press

SYS

CONF

M/S

, to set the

UPLINK MODE to be “Master”. Press

UPLI

, to set the UPLINK to be

“

”

⚫

Set all other machines to be slave machines. Press

SYS

CONF

M/S

, to

set the UPLINK MODE to be “

Slave

”. Press

UPLI

, to set the UPLINK to be

“

”

. Repeat this step to set all slave machines.

⚫

Connect all FY8300 in parallel by SYNC connecter.

⚫

The uplink machines cannot exceed 8 because the driving ability.

When the setting above has been finished, all machines in network will work

synchronously according to the start phase of master machine. When outputting
signal with same frequency, multi channels output can be executed with phase
adjustable.

Содержание FY8300 Series
















































Результаты поиска

Содержание FY8300 Series

Отзывы:

Похожие инструкции для FY8300 Series

Бренды по названию

Популярные бренды

FeelElec FY8300 Series, Руководство пользователя

Результаты поиска

Содержание FY8300 Series

Отзывы:

Похожие инструкции для FY8300 Series

Бренды по названию

Популярные бренды