FeelElec FY8300 Series Скачать руководство пользователя страница 40

Страница: 40 / 47

FeelElec

FY8300 Series User

’

s Manual

Configuration

Press

SYS

button to enter system interface. Then press

CONF

button to enter

system configuration interface. Press corresponding buttons to select system
work mode.

⚫

Press

中文

button to select Chinese as system language.

⚫

Press

Eng

button to select English as system language.

⚫

Press

BUZZ

button to turn on/off buzzer. On is the default.

⚫

Press

PHAS

button:

The phase of the three output waveforms can be

set in manual/automatic state. When the waveform parameters are

adjusted, the phase of the three output waveforms is asynchronous until

the user enters the interface of adjusting the phase. When the automatic

state is activated, the phase of the three output waveforms keeps

synchronous.

⚫

Press

M/S

button to set uplink mode: Master/Slave. Master is the

default.

⚫

Press

UPLI

button to turn on/off uplink function. Off is the default.

Содержание FY8300 Series
















































Результаты поиска

Содержание FY8300 Series

Отзывы:

Бренды по названию

Популярные бренды

FeelElec FY8300 Series, Руководство пользователя

Результаты поиска

Содержание FY8300 Series

Отзывы:

Бренды по названию

Популярные бренды