FeelElec FY8300 Series Скачать руководство пользователя страница 38

Страница: 38 / 47

FeelElec

FY8300 Series User

’

s Manual

System Configuration and Auxiliary Functions

Press

SYS

button of front panel to enter System interface. The interface

displays the instrument parameter storage [SAVE] , parameter loading [LOAD] ,
configuration [CONF] and other functional [MORE] information.

SAVE: To save current parameters of waveform to save positions (12 sets).
LOAD: To load parameters to current working status from save positions.
SYNC

：

The waveform parameters of configurable channels 2 and 3 change

synchronously with the corresponding parameters of channel 1.

CONF: To set system language, turn on/off Buzzer and Uplink mode.
MORE: To set default output status of three channels.

CH1 BOOT

：

The default CH1 channel is on to turn on the output state

，

can press the [ F1 ]

button to set the default output status of the CH1 channel.

CH2 BOOT: ON

The default CH2 channel is on to turn on the output state

，

can press the [ F2 ]

button to set the default output status of the CH2 channel.

CH3 BOOT: ON

The default CH3 channel is on to turn on the output state

，

can press the [ F3 ]

button to set the default output status of the CH3 channel.

FACTORY DEFAULTS:OFF

According to user's requirement, factory settings can be restored by pressing

F3 key and

key.

Содержание FY8300 Series
















































Результаты поиска

Содержание FY8300 Series

Отзывы:

Бренды по названию

Популярные бренды

FeelElec FY8300 Series, Руководство пользователя

Результаты поиска

Содержание FY8300 Series

Отзывы:

Бренды по названию

Популярные бренды