Feel Good mr steam Fifth Avenue H542 Скачать руководство пользователя

Страница: 10 / 12

steam

Hydronic Towel Warmers

Installation and Operating Instructions

________________________________________________________________

______________________________________

H O T W A T E R T O W E L W A R M E R S

______________________________________

Dimensions

(inches)

__________________

Model H

W D BTU/hr

†

Weight

(lbs.)*

______________________________________

H542

⁄

500

______________________________________

†

At 158˚ F *

without water

WALL PREPARATION

• DO NOT mount the Towel Warmer without providing

structurally secure headers as shown.

• DO NOT mount the Towel Warmer directly to sheet rock

or any other non-structural surface.

• Use longer fasteners as required if the finished wall surface

prevents adequate mounting with the screws provided.

• The recommended location for the optional lower brackets is

on the bottom most rung of the Towel Warmer as shown.

*Inlet/outlet pipe to be 18

⁄2” apart for all models

IMPORTANT NOTE:

Towel Warmers may have small dimen-

sional variations and must be measured prior to installation.

For Technical Service Assistance: East Coast Tel: 1-800-767-8326
West Coast Tel: 1-800-727-8326

(optional)

Minimum

Header

Size

2"x 6"

18.5"

Inlet/Outlet Pipe

Center to Center

22" Min Header Length

Sliding Escutcheon

Set Screw

Towel Warmer

Header

Finished surface of wall

Brass Insert

Screw

STEP 1: PRE-INSTALLATION

A. Select Installation Site: Make certain there is ample clear-

ance on both sides and back of the Towel Warmer.

NOTE:

This unit is supplied with the proper hardware for

installation. Be sure wall construction is appropriate for hang-

ing (see Step 3A, pg.11).
B. Before beginning the installation of any Mr.Steam Hydronic

Towel Warmer, please note the following:

Maximum operating temperature should not exceed 158°F.

Any working water temperature higher than 158°F could

create a potential burn hazard.

NOTE:

A closed loop non-potable hot water system is rec-

ommended. Consult an authorized hot water system installer

for hot water system types.

STEP 2: INSPECT THE TOWEL WARMER

A. Unpack the Mr.Steam Towel Warmer carefully to avoid any

damage or loss of any part. When opening the box and

unwrapping the Towel Warmer, be sure that parts are not

accidentally discarded (see illustration, Fig 1, pg.9).

B. Mr.Steam Hydronic Towel Warmers are shipped in spe-

cially designed shipping cartons. The entire surface of the

Towel Warmer is hand-wrapped to protect the finish. Check

the for any sign of damage.

CAUTION

MODEL

H 542

⁄

MOUNTING DIMENSIONS

(inches)

Содержание mr steam Fifth Avenue H542













Результаты поиска

Содержание mr steam Fifth Avenue H542

Отзывы:

Похожие инструкции для mr steam Fifth Avenue H542

Бренды по названию

Популярные бренды

Feel Good mr steam Fifth Avenue H542, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание mr steam Fifth Avenue H542

Отзывы:

Похожие инструкции для mr steam Fifth Avenue H542

Бренды по названию

Популярные бренды