Feel Good mr steam Fifth Avenue H542 страница 11 Скачать руководство пользователя

Страница: 11 / 12

steam

Hydronic Towel Warmers

Installation and Operating Instructions

________________________________________________________________

1/2 inch

3/4 NPT

(Eccentric

Coupling

not used)

F lush

1/2 NPT

Coupling

or thread-to-sweat

adapter to be flush

with finished face

of wall.

PLUMBING PREPARATION

• If the eccentric coupling is used, a female 1/2

NPT coupling or thread-to-sweat adapter should
be flush with the finished face of the wall.

• If the eccentric coupling is not used a male 3/4

NPT pipe, coupling or thread to sweat adapter
shall be 1/2 an inch beyond the finished face of
the wall.

HYDRONIC HOOK-UP

Hydronic Towel

Warmer

Supplied with
Towel Warmer

Field Supplied

Eccentric
coupling
(optional)

Straight
coupling
(or similar)

Field Plumbing

Escutcheon

Washer

Valve

Union

STEP 3: INSTALLATION

A. Mounting:

1. The Mr.Steam Towel Warmer has been designed with

integral mounting brackets. These will facilitate a permanent

and secure mounting of the Towel Warmer to the wall using

the screws provided.

2. Locate the brass inserts according to the following chart:

(All inlet/outlet pipes are 18 1/2” apart.)

3. Slide a bracket escutcheon (with the ‘O’ ring facing the towel

warmer) on each of the mounting brackets.

4. Slide the towel warmer on the brass inserts and tighten the set

screws on both brackets. Slide the escutcheons against the

wall to hide the joint.

5. The recommended location for optional lower brackets is on

the bottom rung of the Towel Warmer, a sufficient header

should be provided for these brackets.

Vertical Distance from Inlet/Outlet Pipe centerline

H542 6-7/16”

Towel

Warmer

Union

Washer

Valve

Содержание mr steam Fifth Avenue H542













Результаты поиска

Содержание mr steam Fifth Avenue H542

Отзывы:

Похожие инструкции для mr steam Fifth Avenue H542

Бренды по названию

Популярные бренды

Feel Good mr steam Fifth Avenue H542, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание mr steam Fifth Avenue H542

Отзывы:

Похожие инструкции для mr steam Fifth Avenue H542

Бренды по названию

Популярные бренды