background image

mr

.

steam

®

 

Electric Towel Warmers

   

Installation and Operating Instructions

________________________________________________________________

 

INSTALLER:

_

______________________________________________________

READ THIS ENTIRE INSTRUCTION MANUAL THOROUGHLY 

BEFORE BEGINNING INSTALLATION. LEAVE  THESE 

INSTRUCTIONS WITH HOMEOWNER.

   

BE CERTAIN ELECTRICITY IS SHUT OFF 

AT MAIN PANEL BEFORE WIRING OR SERVICING YOUR 

TOWEL WARMER. Follow instructions to make certain your 

Towel Warmer is properly attached to the wall. FAILURE TO 

FOLLOW THESE STEPS COULD RESULT IN HAZARDOUS 

CONDITIONS.

   

To avoid possible fire hazard, the Towel 

Warmer must remain in its intended position. MOUNT  

THIS UNIT ONLY AS SHOWN IN THESE INSTRUCTIONS.  

DO NOT alter or modify any Mr. Steam products. Doing so 

may result in an inoperable or hazardous installation and will 

void the warranty.

1. Install in accordance with  

National and local codes.

2. Do not locate in shower  

stall or near shower spray.

3. Do not locate within the  

shower or tub zone.

4. All models are to be pro- 

tected by dedicated and suitably  

rated GFCI circuit breaker or equal.

TO ENSURE CORRECT OPERATION OF YOUR TOWEL WARMER,  

PLEASE FOLLOW ALL THE INSTRUCTIONS CAREFULLY, 

OBSERVING THE “CAUTION” NOTATIONS FOR EACH STEP.

Inspect Towel Warmer

Unpack the Towel Warmer carefully to avoid any damage or  

loss of any part. When opening the box be sure that the parts 

are not accidentally discarded. Towel Warmers are shipped in 

specially designed shipping cartons. The entire surface of the 

Towel Warmer is hand-wrapped to protect the finish. It is your 

responsibility 

to immediately inspect for any damage.

HOMEOWNER:

__________________________________________

THANK YOU for selecting Mr.Steam Towel Warmer, the 

perfect addition to bathrooms, family spas, and exercise 

rooms within your home. Our products have long been 

a standard for quality and comfort, and we are sure that 

you will experience continued enjoyment from the Towel 

Warmer you have purchased by following these simple 

instructions.

 

TOWEL WARMERS ARE HOT!  The 

Towel Warmer is an electrical heating appliance, intended 

only for indoor residential applications and, as such, 

should be installed and used with  certain precautions for 

your safety.

1. INSTALLATION PROCEDURES FOR PERMANENTLY 

WIRED WALL-MOUNTED UNITS MUST BE 

ACCOMPLISHED BY QUALIFIED PERSONNEL IN 

STRICT ACCORD WITH APPLICABLE NATIONAL AND 

LOCAL BUILDING AND ELECTRICAL CODES.

2. DO NOT place TOWEL WARMER units inside a shower, 

sauna or steam room enclosure or any other wet loca-

tion or with elevated temperatures.

3. CAUTION is advised when Towel Warmer is accessible 

to children.

4. For the ultimate ease in use, a dedicated wall switch 

or timer can be used to control the TOWEL WARMER 

unit. Contact Mr.Steam for an in-wall 24-hour-7 day 

timer (PN W-103588) NOTE: All switches and control 

devices must be installed on the load (black) side of the 

Towel Warmer circuit in compliance with the National 

Electric Code and Local Codes. (see page 8 for installa-

tion instructions)

IMPORTANT:

 The finish of your Towel Warmer can be 

protected and maintained by an occasional wiping with 

a soft, non-abrasive, damp cloth and lightly polished, 

thereafter, with a soft dry cloth when the Towel Warmer 

is cold. Under no circumstances should abrasive cleaning 

powders, metal polish or chlorine-based cleaners be used 

on any part of this product.

IMPORTANT:

 This appliance is intended for towels 

washed in water. Fabrics that contain soap or deter-

gent residue may show what appears to be scorch 

marks. However this is simply the discoloration of the 

residue. The Towel Warmer unit does not reach suffi-

cient temperature to scorch fabric. We are not respon-

sible for discoloring or damage 

of any fabrics.

This picture shows the recom-

mended  method of draping a 

towel on a towel warmer. Ensure 

that as much as possible of the 

towel’s surface is touching the 

towel warmer to ensure fast  

even warming of the towel

2

!

WARNING

!

WARNING

!

WARNING

!

CAUTION

Shower/Tub 

Zone

Do not locate the 

towel warmer within 

the shower/tub zone

For illustrative purposes only

TOWEL WARMER SPECIFICATIONS

_____________________________________________________________

  

Dimensions (inches) 

 

Model No.  W x H x D 

Amps 

Volts/Phase  Weight (lbs.)

_____________________________________________________________

W500 

22.5 x 25 x 5 

0.83 

120/1 

20

_____________________________________________________________

W542 

23.75 x 26 x 5.25  1.25 

120/1 

25

_____________________________________________________________ 

W634 

19.5 x 27.5 x 7.25  1.67 

120/1 

25

_____________________________________________________________

Содержание mr steam Fifth Avenue H542













Отзывы: