Federal RSSD360 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 76

Federal RSSD360 Скачать руководство пользователя страница 6

PRE-INSTALLATION PROCEDURES

Inspection For Shipping Damage

               You are responsible for filing all freight claims with the delivering truck line.
               Inspect all cartons and crates for damage upon arrival. If there is damage to
               shipping crates, cartons, or if a shortage is found, note this on (all copies) of
               the Bill Of Lading prior to signing.

               If damage is discovered when the case is uncrated, immediately call the delivering
               truck line and follow-up the call with a written report indicating concealed damage to
               your shipment.  Ask for an immediate inspection of your concealed damaged item.
               Crating material must be retained and shown to the inspector from the truck line.

INSTALLATION INSTRUCTIONS

Locating the Display Case

NOTE: This case is designed for indoor use only.

The case should be

located

where it is not subjected to the direct rays of the sun,

heating ducts, grills, radiators, or ceiling fans, nor should it be located near open doors or

main door entrances. Avoid locations where there is excessive air movement or air

disturbances and avoid high humidity locations such as near cases with water misting or

fogging devices.

The condenser air inlet is located in the front center of the base. Do not block this inlet and

do not locate the air inlet near a source of heat. Prior to 01/01/20 clearance of 6” minimum

must be maintained at the back of the case for condenser discharge air. After 01/01/20 the

case requires no clearance at the back of the unit unless it has rear condenser air intake and

discharge. Clearance at the top of the case should also be at least 8”.

Do not build this unit into an alcove and do not locate where condenser discharge air

cannot escape or where warm condenser air is allowed to re-circulate.

Grill Removal

WARNING

:

Electrical shock hazard. Do not operate unit with panels removed.

Must remove front and rear base grills for merchandiser installation. The front base side grilles

are secured with self-threading screws located in the top grille rail, and the rear base grill is

secured with self-threading screws.

These base grills must be replaced after merchandiser installation. Base grills must be

in place for proper operation of the merchandiser.

Refrigerated Self-Serve Merchandiser (High Profile)

Page 3

«
...
4
5
6
7
8
...
»

Содержание RSSD360













































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды