Federal ITD Series Скачать руководство пользователя страница 28

Страница: 28 / 64

- 28 -

Joining Floor Model Bases (No End Panels Between)

The cases are joined in the same manner as described in previous

Joining Cases

section

but the bases will also need to be joined.

Push cases together and align front and rear of cases.

Remove the base front and back panels as described in

Refrigeration Compartment Panel Removal

Section.

Push cases together and align front and rear of cases and bases. If there is a miss-alignment between

cases and the bases, it may be necessary to loosen the screws holding the case to the base. The

mounting brackets are located inside the top of the base and there are (2) in the front and (2) in the

back. This will allow slight adjustment to improve alignment. Retighten these screws once components

are properly aligned

Attach the cases together using (5) 10-32 screws and nuts provided. Attach in the (5) Key slot location

shown in above diagram. There are no fasteners used on the (2) center key slots.

Tighten all joining screws and nuts in base and case at this time.

Trim the front of base by hooking Base joining trim strip under base valance and up over the top of

base trim.

Mark the base in the location of the top holes in the base join trim strip. Drill (2) 9/64 holes in base and

fasten base join trim strip to base using (2) 8-32 screws provided. Attach Join Trim Strip with (2) 8-32

self-tapping screws.

Содержание ITD Series

































































Результаты поиска

Содержание ITD Series

Отзывы:

Похожие инструкции для ITD Series

Бренды по названию

Популярные бренды

Federal ITD Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание ITD Series

Отзывы:

Похожие инструкции для ITD Series

Бренды по названию

Популярные бренды