background image

Valor

®

 Light Bar Hook-On Mounting Kit Manual

7

Valor Hook-On Mounting Kit 

Federal Signal

 www.fedsig.com

Adjusting the Optional HotFoot LED Alley Lights

The optional HotFoot LED alley lights are factory-installed and wired. The factory position is 10 degrees 

forward. The lights are horizontally adjustable up to –10 degrees.
To horizontally adjust the alley lights:

1. 

Loosen the 10-32 Keps

®

 nuts on the underside of the HotFoot as shown in Figure 6.

2. 

Reposition the lights and tighten the 10-32 Keps nuts.

Figure 6 LED HotFoot takedown and alley lights

LED TAKEDOWN LIGHT

10-32 KEPS NUTS

290A6451

LED ALLEY LIGHT

Getting Technical Support

For technical support, please contact:
Federal Signal Corporation  

Service Department 

Phone: 1-800-433-9132 

Email: [email protected]

Getting Repair Service

The Federal Signal factory provides technical assistance with any problems that cannot be handled locally. 

Any product returned to Federal Signal for service, inspection, or repair must be accompanied by a Return 

Material Authorization (RMA). Obtain a RMA from a local Distributor or Manufacturer’s Representative. Provide 

a brief explanation of the service requested or the nature of the malfunction. 
Address all communications and shipments to the following: 

Federal Signal Corporation  

Service Department  

2645 Federal Signal Dr.  

University Park, IL 60484-3167

Содержание Valor Hook-On









Отзывы: