Fayat Group Dynapac DFP11 Скачать руководство пользователя страница 68

Страница: 68 / 114

7.1 Loading the machine

Loads may only be attached and hoisted by an expert/qualified

person.

Do not use lifting points that are damaged or impaired in any other

way.

Only use lifting and lashing tackle with sufficient load bearing

capacity for the weight to be loaded. Minimum load bearing

capacity of lifting tackle: see operating weight

Chapter 2 „Tech-

nical data“ on page 11

Always use appropriate lifting and lashing tackle at the lifting and

lifting points.

Use lifting tackle only in the specified loading direction.

Lifting tackle must not be damaged by machine parts.

When lifting the machine, make sure the load does not move in an

uncontrolled way. If necessary, hold the load steady with guide

ropes.

Protective equipment:

Working clothes

Hard hat

Safety shoes

Protective gloves

Park the machine safely

Chapter 6.5 „Parking the machine

in secured condition“ on page 64

Allow the engine to cool down.

Fold the guide handle forwards.

Attach the lifting tackle to the dedicated lifting eye.

DANGER!
Danger to life caused by suspended

loads!

–

Do not step or stand under suspended

loads.

Lift the machine carefully and set down again at the intended

location.

B-230-0069

Fig. 47

Loading/transporting the machine – Loading the machine

DFP11

Содержание Dynapac DFP11



















































































































Результаты поиска

Содержание Dynapac DFP11

Отзывы:

Fayat Group Dynapac DFP11, Руководство по эксплуатации, Страница: 68 / 114

Результаты поиска

Содержание Dynapac DFP11

Отзывы: