Fayat Group Dynapac DFP11 Скачать руководство пользователя страница 16

Страница: 16 / 114

3.1 Basic prerequisites

3.1.1 General

This machine has been built in compliance with the latest technical

standard and complies with the applicable regulations and tech-

nical rules.

However, dangers for persons and property may arise from this

machine, if:

it is used for purposes other than the ones it is intended for,

it is operated by untrained personnel,

it is changed or converted in an unprofessional way,

the safety instructions are not observed.

Each person involved in the operation, maintenance and repair of

the machine must therefore read and comply with these safety reg-

ulations. If necessary, the operating company must obtain the rele-

vant signatures as confirmation.

Furthermore, the following obviously also applies:

applicable accident prevention instructions,

generally accepted safety and road traffic regulations,

country/state specific safety regulations.

It is the duty of the operator to be acquainted with the safety regu-

lations and to apply these accordingly. This also applies for local

regulations and regulations concerning different types of handling

activities. Should the recommendations in these instructions be dif-

ferent from the regulations valid in your country, you must comply

with the safety regulations valid in your country.

3.1.2 Explanation of signal words used:

DANGER!
Danger to life if failing to comply!

Sections marked accordingly indicate an extremely

dangerous situation that could lead to fatal or

severe injuries, if this warning is disregarded.

WARNING!
Danger to life or danger of severe injuries if

failing to comply!

Sections marked accordingly indicate a dangerous

situation that could lead to fatal or severe injuries,

if this warning is disregarded.

Concerning your safety – Basic prerequisites

DFP11

Содержание Dynapac DFP11



















































































































Результаты поиска

Содержание Dynapac DFP11

Отзывы:

Fayat Group Dynapac DFP11, Руководство по эксплуатации, Страница: 16 / 114

Результаты поиска

Содержание Dynapac DFP11

Отзывы: