Fayat Group CP1200 Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 86

Fayat Group CP1200 Скачать руководство пользователя страница 60

Preventive maintenance

56

4812325556EN

08/01/2023

Preventive Maintenance

Introduction

It  is  necessary  to  carry  out  a  complete  maintenance  so  the
machine  can  work  satisfactorily  and  at  the  lowest  possible
costs.

The  Maintenance  section  includes  the  periodic  maintenance
that shall be carried out on the machine.

The  recommended  maintenance  intervals  assume  that  the
machine  is  being  used  in  a  normal  environment  and  working
conditions.

Delivery

The machine is tested and adjusted before leaving the plant.

The  inspection  shall  happen  in  the  moment  it  arrives  to  the
client, following the list in the warranty document.

Any  transport  damage  shall  be  immediately  reported  to  the
carrier company.

Warranty

The warranty is only valid if the inspections were carried out at
the time of the delivery, as well as the maintenance inspections
according to the warranty.

The warranty is not valid if there are damages due improper
assistance, misuse of the machine, use of lubricants and
hydraulic oils not specified in the manual or if other adjustments
were made without the proper authorization.

Warning symbols

WARNING! Damage to the machine or its parts.

CAUTION! Risk of death or injures.

«
...
58
59
60
61
62
...
»

Содержание CP1200























































































Отзывы:

Нет отзывов