manualshive.com logo in svg

Fayat Group CP1200, Инструкция по эксплуатации, Страница: 16 / 86

Поделиться
Скачать
Fayat Group CP1200 Скачать руководство пользователя страница 16

 

Safety decals - description and location 

 

12 

4812325556EN 

08/01/2023 

 

Safety decals - Description and 
location (cont.) 

 

Always  make  sure  that  all  the  safety  decals  are 
completely legible and remove the dirt or request for 
new  ones  if  they  are  illegible. Use  the  part  number 
indicated on each decal. 
 

1 

 
 
 
 
 

WARNING: 
Crush zone, wheel.  
Keep a safe distance from the crush zone.

 

2 

 
 
 
 
 

WARNING:  
Rotating engine components, be careful!  
Keep your hands off the danger zone.

 

3 

 
 
 
 
 

WARNING:  
Hot surface!  
Keep your hands off the surface.

 

4 

 
 
 
 
 

WARNING:  
Read  carefully the towing chapter before releasing 
the brakes. Crushing injury danger. 

 

5 

 
 
 
 
 

WARNING:  
The  operator  must  read  the  Safety  and  Engine 
Manuals, as well as the Operation and Maintenance 
instructions. 

 

6 

 
 
 
 
 

WARNING:  
High pressure fluid.  
Make  sure  to  release  the  pressure  from  the 
accumulators before opening the hydraulic system. 

 

7 

 
 
 
 
 

WARNING:  
Gas shall not be used to start the machine. 

 

8 

 

 
 
 
 

WARNING: 
Ultra low sulfur fuel only. 
Tier IV 

 

 

Содержание CP1200























































































Отзывы:

Нет отзывов