manualshive.com logo in svg

Faulhaber Series MCBL 3002/03/06 RS/CF /CO, Техническое руководство, Страница: 13 / 32

Поделиться
Скачать
Faulhaber Series MCBL 3002/03/06 RS/CF /CO Скачать руководство пользователя страница 13

13

3 Installation

3.1  Assembly instructions

Surface

Motion Controllers may be screwed onto flat, hard surfaces only. The surface must be suitable for 
supporting the assembly sleeves against the screwing forces. Screwing onto a soft or uneven surface 
can cause the assembly sleeves to be pressed out.

Right

The Motion Controller is mounted on a flat, 
hard surface.

Wrong

The Motion Controller is screwed on over an 
edge. Risk of pushing out the assembly sleeves!

Screw-type terminal strips

The maximum tightening torque of the screw-type terminal strips must be noted and observed.
For series MCxx 3002 S: min. 0.12 Nm; max. 0.15 Nm
For series MCxx 3006 S: min. 0.5 Nm; max. 0.6 Nm

Flexboard connector

The motors' flexboards must be inserted into the connector flat. The connector pin assignment and 
connection symbols must be noted.
Never press the flexboard into the connector with force as this could damage it. If necessary, use a 
suitable tool (for example, tweezers or a flat-nose pliers). Ensure the flexboard is not squeezed or 
crushed.

Содержание Series MCBL 3002/03/06 RS/CF /CO

































Отзывы:

Нет отзывов