Fastwel CPC308 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 81

background image

CPC308 Processor Module

C P C 3 0 8 U s e r M a n u a l

© 2 0 1 3 F a s t w e l V e r . 0 0 1 b E

8

Safety Requirements

This product of Fastwel Group Co. Ltd has been developed and tested with the purpose of

ensuring its compliance with electrical safety requirements. Its design provides long-term trouble-
free functioning. The product service life can be significantly shortened because of its incorrect
handling during unpacking and installation. Therefore, for your safety and ensuring of the correct
operation of the product you should adhere to the recommendations given below.

High Voltage Safety Rules

Any work with this device must be performed only by sufficiently skilled personnel.

Before installing the board into your system, make sure that the mains power supply is

disconnected. This is also true for the installation of expansion boards.

There is a serious hazard of electrocution in the process of the product installation, repair

and maintenance; therefore, always unplug the power cord during work performance. This is also
true for other power cables.

Board Handling Instructions

Electronic boards and their components are static sensitive. Therefore, special attention is

needed to ensure safety and normal operation while handling those devices.



Do not leave the board without protective package when it does not operate.



Always work with the board on static-safe workplaces if possible. If it is impossible, the
user must remove static charge from him/herself before touching the product with
his/her hands or tools. This is best done by touching a metal part of the system body.



It  is  especially  important  to  observe  precaution  while  replacing  expansion  boards,
jumpers,  etc.  Since  there  is  a  battery  powering  memory  and  real-time  clock  on  the
board,  do  not  put  it  on  conductive  surfaces,  like  antistatic  carpets  or  sponges.  They
may cause a short circuit and inflict damage to the battery and the board conductors,
as well as loss of real-time clock (RTC) data.

«
...
6
7
8
9
10
...
»

Содержание CPC308


















































































Отзывы:

Нет отзывов

Похожие инструкции для CPC308

Бренд: Yamaha Страницы: 82

Бренд: Quantum Страницы: 69

TPS61090EVM-029

Бренд: Texas Instruments Страницы: 19

Бренд: JETWAY Страницы: 44

Бренд: Aaeon Страницы: 44

Бренд: Texas Instruments Страницы: 8

Бренд: Texas Instruments Страницы: 18

Бренд: Gigabyte Страницы: 76

Бренд: Abit Страницы: 110

Бренд: Alinx Страницы: 29

Бренд: Gigabyte Страницы: 39

Бренд: Seanix Страницы: 54

Бренд: Gigabyte Страницы: 96

Бренд: TYAN Страницы: 54

Бренд: Panasonic Страницы: 5

Бренд: Panasonic Страницы: 11

PGA26E07BA-SWEVB006

Бренд: Panasonic Страницы: 17

Бренд: Panasonic Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды