Fascut 19547 Скачать руководство пользователя | Manualshive

Страница: 39 / 39

background image

FASCUT

®

Industries, Inc.

LIMITED WARRANTY

This product has been thoroughly inspected and tested before leaving the factory. It is guaranteed
against defective workmanship and materials for a period of 1 year to the original owner. Should any
trouble develop, return defective part transportation prepaid to the factory. If inspection shows trouble
is caused by defective workmanship or material, all repairs will be made without charge and returned,
transportation prepaid. The guarantee does not apply where: repairs or attempted repairs have been
made by persons other than the factory; repairs are due to normal wear; the tool has been abused or
in an accident; misuse is evident

– caused by overloading the tool beyond its rated capacity; use on

improper voltage or current; use of the tool after partial failure or use with improper accessories.

This warranty is in lieu of all other warranties, expressed or implied, and there are no warranties on
merchantability or fitness for a particular purpose. In no event shall seller be liable for incidental,
consequential or special damages. This warrantee is void if Warrantee/Registration card is not filled
out and returned. This warranty gives you specific legal rights, and you may also have other rights,
which vary from state to state.

SERIAL NUMBER ______________________ DATE ____________________

FASCUT®

Industries, Inc.

7248 Inama Rd.

Sauk City, WI 53583

Phone:

(608) 643-6678

Fax:

(608) 643-2682

www.fascut.com

«
...
37
38
39

Содержание 19547








































Отзывы:

Нет отзывов

Похожие инструкции для 19547

Бренд: ABB Страницы: 11

Бренд: Fender Страницы: 15

Бренд: J D Squared Страницы: 18

Бренд: Taylor Страницы: 70

Бренд: Kane Страницы: 16

Бренд: HAMAR LASER Страницы: 49

Бренд: Cambro Страницы: 6

Бренд: G-Lab Страницы: 16

Бренд: G&G Страницы: 2

Бренд: Hakko Electronics Страницы: 8

Professional HS 8

Бренд: Hailo Страницы: 5

Бренд: Hainbuch Страницы: 52

Бренд: Raven Страницы: 48

Бренд: Pacific Страницы: 16

MCX-C15 - MusicCAST Network Audio Player

Бренд: Yamaha Страницы: 65

Бренд: Yamaha Страницы: 24

Бренд: uniprox Страницы: 3

Бренд: Ultrasport Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды