Fascut 19547 Скачать руководство пользователя

Страница: 38 / 39

Cutting blades
breaking

1.  Blades are dull.
2.  Blade bolts are loose.
3.  Material is being dropped into

the cutter.

4. You are cutting hardened

steel

5. Material is being cut on the

top corner of the cutting blade

1. Turn blades to a new edge

sooner.

2. Check blade bolts for

tightness more often.

3. Place material into the

cutter with greater care.

4. Do not cut hardened

material.

5. Material must rest on the

bottom of the cutter
opening.

Oil is leaking

1. Hydraulic tubes and fittings

are loose or damaged.

2. Hydraulic cylinder body seals

or rod seal is leaking.

3. Oil is leaking from rotary

actuator.

1. Check fittings for tightness.

Replace damaged fittings
or tube.

2. Install new body and/or rod

seals in hydraulic cylinder.

3. Install new seals and o-

rings in rotary actuator.

Bending or
Cutting is slow
and lacks power

1.  Oil level is low.
2.  Oil is contaminated.
3.  Hydraulic pump is worn.

1. Add oil to tank.
2. Drain and refill oil tank with

fresh ISO-46 hydraulic oil.

3. Replace hydraulic pump.

Содержание 19547








































Результаты поиска

Содержание 19547

Отзывы:

Похожие инструкции для 19547

Бренды по названию

Популярные бренды

Fascut 19547, Инструкция по эксплуатации

Результаты поиска

Содержание 19547

Отзывы:

Похожие инструкции для 19547

Бренды по названию

Популярные бренды