FarmTek Growers Supply GrowSpan Round Pro Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 51

background image

GROWSPAN

™

ROUND PRO GREENHOUSES AND SYSTEMS

36

Revision date: 01.03.19

SHELTER CARE AND MAINTENANCE

Proper care and maintenance of the shelter is important.

Check the following items periodically to properly maintain

the shelter:
• Regularly check the cover or covers to see that these

are tight and in proper repair. Tighten and adjust the

tension as needed to prevent damage and wear.

• Check the cable turnbuckles and cable clamps to see

that these remain tight. Tighten as needed.

• Check connections and all fasteners to verify that they

remain tight and in good condition.

• Check the polycarbonate panels to verify that these

are secure and in good repair. Verify that nothing is

touching the panels that may cause damage.

• Do not climb or stand on the greenhouse at anytime.
• Remove debris and objects that can accumulate on the

greenhouse. Use tools that will not damage the cover

when removing debris.

• Remove snow to prevent excess accumulation. Use

tools that will not damage the cover when removing

snow.

• Check the contents of the shelter to verify that nothing

is touching the cover that could cause damage.

• If the shelter is dismantled and moved, inspect all parts

and connections before using.

• Depending on the contents, construction of the shelter,

shelter materials, and shelter location, the potential for

condensation exists. GrowSpan™ offers several items

that can be used to alleviate a condensation condition.

Please contact a GrowSpan™ representative for

additional information.

• For replacement or missing parts, call 1-800-245-9881

for assistance.

Space below is reserved for customer notes.

«
...
34
35
36
37
38
...
»

Содержание Growers Supply GrowSpan Round Pro




















































Отзывы:

Нет отзывов

Похожие инструкции для Growers Supply GrowSpan Round Pro

Бренд: Robinsons Страницы: 44

$Poly-Tex FieldPro Gothic High Tunnel 20 Installation Instructions Manual preview$

FieldPro Gothic High Tunnel 20

Бренд: Poly-Tex Страницы: 41

Premium Moo-Tel CD

Бренд: ClearSpan Страницы: 49

Бренд: Plantin Страницы: 32

Dachnaya Tryoshka

Бренд: VOLYA Страницы: 17

Бренд: VOLYA Страницы: 27

Бренд: VOLYA Страницы: 29

Oasis Hex 12' Greenhouse

Бренд: Palram Страницы: 84

Бренд: ACD Страницы: 36

Бренд: Gazebo penguin Страницы: 14

Бренд: Wilko Страницы: 4

Бренд: Vitavia Страницы: 8

Бренд: Vitavia Страницы: 32

Бренд: Costway Страницы: 7

Бренд: Costway Страницы: 22

Бренд: Simplicity Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды