FarmTek Growers Supply GrowSpan Round Pro Скачать руководство пользователя страница 32

Страница: 32 / 51

GROWSPAN

™

ROUND PRO GREENHOUSES AND SYSTEMS

Revision date: 01.03.19

ATTACH CONDUIT TO THE ROLL-UP SIDES

Gather the parts:
•  Assembled conduits
•  Fabric clips #CC6212 (Divide quantity in half.)
•  Tek screws  (#FA4482B)

To this point, the main cover layers are secured to the

greenhouse and the roll-up portion along both sides are

secured to and hanging down from the poly latch double

U-channel.
1. Unfold the remaining portion of the roll-up sides (if

needed) and evenly stretch it out on the ground along

the frame.

2. Working from the inside the frame

, roll the assembled

cover conduit onto the edge of the roll-up side panel.

3. Verify that the side panel and conduit are evenly

positioned and tuck the panel edge under the conduit

and begin to turn the conduit in a clockwise direction.

NOTE:

If the conduit begins to turn inside the side

panel material and is unable to roll up the side evenly,

secure the side panel material to the conduit with

Tek screws and fabric clips evenly spaced along the

conduit.

4. Continue to roll the conduit until the excess side panel

material is wound around the conduit.

5. Repeat these steps for the other side of the shelter.
6. With the excess side panel material rolled up on the

conduit assemblies, continue with the

Twist-of-the-

Wrist Assembly

procedure.

Inside View

Diagram may show a different model and is used for

illustration purposes only.

TWIST-OF-THE-WRIST ASSEMBLY

Gather the parts:
•  Aluminum channel
•  Drive handle
•  Gearbox and gearbox drive
•  Mounting plate
•  Bearing and threaded rod
•  3/8" nuts and washers

The Twist-of-the-Wrist Assembly is designed to roll up a

portion of the sides of the structure. The following steps

describe the assembly and its installation.

1. Drill a 5/16" hole through the cover conduit 1/2" from

the end of the conduit.

2. Insert a tubing adapter into the conduit and align

the holes of the adapter with the drilled holes in the

conduit.

Threaded Rod

Purlin

End

Rafter

Guide

Channel

Carriage

Bolt

Roll-up Side

Conduit

Frame shown

may differ from

actual frame.

Содержание Growers Supply GrowSpan Round Pro




















































Результаты поиска

Содержание Growers Supply GrowSpan Round Pro

Отзывы:

Похожие инструкции для Growers Supply GrowSpan Round Pro

Бренды по названию

Популярные бренды

FarmTek Growers Supply GrowSpan Round Pro, Инструкция по эксплуатации

Результаты поиска

Содержание Growers Supply GrowSpan Round Pro

Отзывы:

Похожие инструкции для Growers Supply GrowSpan Round Pro

Бренды по названию

Популярные бренды