FarmTek Growers Supply GrowSpan Round Pro Скачать руководство пользователя страница 27

Страница: 27 / 51

GROWSPAN

™

ROUND PRO GREENHOUSES AND SYSTEMS

Revision date: 01.03.19

INSTALL POLY LATCH U-CHANNEL

The double poly latch U-Channel (#104211) is attached to

each side of the frame and runs from the front to the back

of the shelter. The position of this U-Channel identifies

the highest "open" position of the roll-up side panels. Tek

screws are used to secure the U-Channel to each rafter

and to secure the splice where two separate U-Channel

sections meet between two rafters.

The single poly latch U-Channel (#102197) is attached

to the top of each end rafter using Tek screws. This U-

Channel is used to secure the center portion of the main

cover that is not part of the roll-up sides. (This is the section

of the main cover that runs down the middle of the frame

at the top stretched between the two runs of double poly

latch U-Channel.) During installation, the single poly latch

U-Channel will bend with the curve of the end rafter as it is

attached.

Gather the parts:

•  Aluminum single U-Channel (#102197): End Rafters
•  Double poly latch Channel (#104211): Sides
•  Tek screws (#FA4482B)

1. Measure the desired height (4'-6') to identify the top of

the roll-up side and mark the location on the end rafter.

2. Move to the other end of the frame and repeat Step 1.
3. Stretch a chalk line between the marks and snap to

mark the location of the double poly latch channel.

4'-6'

Ground Level

Chalk Line

MAIN COVER INSTALLATION

After the end panels and doors are installed, install the

main covers. The steps to install the cover include:
1. Attach poly latch U-Channel along the greenhouse

sides and tops of the greenhouse

end rafters

2. Pull one cover film over the frame and attach to the end

rafters.

3.  Stretch and attach the first cover to the sides.
4.  Install the Inflation Fan kit.
5.  Attach a second cover layer to the frame.
6.  Test the operation of the Inflation fan kit.
7.  Install roll-up side kits and test.

NOTE:

This length of end cap will act as a stop for the

remaining door of the double door when both doors are

closed.

12. Check operation of the latches and doors.
13. Continue with

Main Cover Installation

procedure.

DOUBLE DOOR ASSEMBLY (continued)

11. Next, install another section of end cap on the

inside

frame of the door that includes the chain latch.

Содержание Growers Supply GrowSpan Round Pro




















































Результаты поиска

Содержание Growers Supply GrowSpan Round Pro

Отзывы:

Похожие инструкции для Growers Supply GrowSpan Round Pro

Бренды по названию

Популярные бренды

FarmTek Growers Supply GrowSpan Round Pro, Инструкция по эксплуатации

Результаты поиска

Содержание Growers Supply GrowSpan Round Pro

Отзывы:

Похожие инструкции для Growers Supply GrowSpan Round Pro

Бренды по названию

Популярные бренды