FarmTek Growers Supply GrowSpan Round Pro Скачать руководство пользователя страница 30

Страница: 30 / 51

GROWSPAN

™

ROUND PRO GREENHOUSES AND SYSTEMS

Revision date: 01.03.19

6. As the spring is install the spring into the U-channel

at the top of the first end rafter, ensure that an even

amount of the cover is exposed and maintained along

the edge of the greenhouse.

NOTE:

The cover material is cut longer/wider than

is required to cover the greenhouse. For easier

anchoring, allow approximately 10" to extend past the

edge of the end rafter as the cover is anchored into

place.

7. Stretch the cover to the other end of the building and

repeat the steps to secure the main cover in the single

U-Channel attached to the top of the remaining end

rafter.

NOTE:

Pull the cover tight as the spring is inserted into

the U-Channel.

8. After the cover is stretched end-to-end and secured

using the wire spring and single U-channel, move to

one side of the frame and repeat the steps to anchor

the main cover to the first side.

Begin at one end of the double poly latch channel and

work toward the other.

Use the upper channel of the

poly latch channel to secure the main cover.

Attach main cover to double poly latch channel.

Install the Inflation Fan Kit

before

installing the second

main cover. Consult the instructions included with the

Inflation Fan Kit to install the kit. Actual components

may differ from example shown.

11. After installing the inflation fan kit, repeat the steps to

install the film for the second main cover.

NOTE:

When installing the second cover film, use the

same upper channel used for the first cover film, and

a second run of spring, which is installed on top of the

first U-channel spring already in the channel.

12. With the second cover film layer installed, test the

operation of the inflation fan kit.

IMPORTANT:

If trimming the excess cover material at

the ends and sides, DO NOT remove too much of the

excess material.

Some excess main cover material (the material that

extends beyond the end rafters and sides) should

remain in place to more easily re-stretch the film if

needed.

13. Continue by installing the roll-up side panels.

INSTALL THE ROLL-UP SIDE ASSEMBLIES

The instructions below describe how to install a single

roll-up sidewall assembly for one side of the frame. The

procedure is repeated for the remaining side.

The procedures to install the roll-up side include the

following:
1.  Install roll-up panels.
2.  Assemble the roll-up side conduit.
3.  Attach the roll-up conduit to the bottom of the roll-up

sides.

4. Assemble the Twist-of-the-Wrist assembly and attach it

to the frame and the roll-up side.

5. Install the Anti-Billow Rope system.
6. Test the operation of the roll-up side.

INSTALL MAIN COVER (continued)

NOTE:

Maintain an even length along the side. The

final stretching of the cover takes place when the last

side is secured.

9. After securing the first side, move to the remaining

side, pull the cover tight, and secure it in place as

previously described.

10. Once the first cover is stretched and secure, install the

inflation fan kit in the desired location and according to

the instructions sent with the kit.

Содержание Growers Supply GrowSpan Round Pro




















































Результаты поиска

Содержание Growers Supply GrowSpan Round Pro

Отзывы:

Похожие инструкции для Growers Supply GrowSpan Round Pro

Бренды по названию

Популярные бренды

FarmTek Growers Supply GrowSpan Round Pro, Инструкция по эксплуатации

Результаты поиска

Содержание Growers Supply GrowSpan Round Pro

Отзывы:

Похожие инструкции для Growers Supply GrowSpan Round Pro

Бренды по названию

Популярные бренды