FarmTek 104299 Скачать руководство пользователя

Страница: 8 / 13

CHICK-INN

Revision date: 12.19.07

LAY OUT THE BUILDING SITE

After the site is prepared, identifying the location of

the shelter corners helps to square the frame after it is

assembled.

Taking these steps

before

assembling the shelter saves

time and ensures that the structure is positioned as

desired. The following procedure is a suggested method. Its

use depends on the size of the shelter, shelter application,

the footings, and the method used to anchor the shelter.

SQUARE THE SITE

1. Identify where a corner of the building will be

positioned, drive in a stake. String a line the exact

width of the building and drive another stake.

2. Sting a line 90 degrees from the string at least as long

as the building and drive a stake at one back corner.

3. Measure the width and length of the building and drive

the final corner stake.

NOTE:

A transit can be used to ensure an accurate 90°

angle, or the 3-4-5 rule can be used. Refer to diagram.

Using multiples of 3-4-5 such as 6-8-10 or 12-16-20

helps to maintain an accurate 90° angle.

4. After squaring the position of the building and placing

a stake at all corners, string a line between the stakes

to mark the base of the building.

RAFTER ASSEMBLY

Gather the parts:
•  Pipes 1.315" x 78" Plain (#131P078)
•  Pipes 1.315'' x 72" Plain (#131P072)
•  3-Way Couplers (#102191)
•  4-Way Couplers (#102192)

Rafter Assembly Procedure

Arrange the roof pipes on the ground adjacent to the

correct couplers needed to assemble the roof.
1. Connect the ridge pipes (72" purlin section) using a

3-Way coupler on each end and 4-Way couplers

between the sections. The length should match your

shelter length.

NOTE:

The last ridge pipe will finish with a 3-Way

coupler.

2. Attach the rafter pipes as shown in the illustration.

Rafter pipes are 78".

3. Connect the 3-Way couplers to assemble the end

rafters of the roof assembly and connect the 4-Way

couplers to construct the inside rafters.

NOTE:

Position the couplers with the eye bolts inside

the frame.

Inside

Rafter

78"

72"

End

Rafter

Ridge

Pipe

4-Way Coupler

3-Way

Coupler

Inside

Rafter

End

Rafter

Содержание 104299














Результаты поиска

Содержание 104299

Отзывы:

Похожие инструкции для 104299

Бренды по названию

Популярные бренды

FarmTek 104299, Руководство пользователя

Результаты поиска

Содержание 104299

Отзывы:

Похожие инструкции для 104299

Бренды по названию

Популярные бренды