208
(MT11 - Gb2006)
The installation of the caller identifier board (art. ES70) into the FT105P
or FT208P PABX allows you to display the caller’s telephone number.
The board allows for connecting up to 4 terminals. The service must be
requested to the telephone provider.
Installing the board into the PABX
Check that the PABX is turned OFF
Remove the cover by unscrewing the 2 top screws
Fix the board on the provided space
Connect the ES70 board cable to the JP4 connector of the PABX (fax-
switch board)
Connect the 2 wires of each external line to the URB1 and URB2
terminal boards of the PABX and the ES70 board
Remember to correctly program the PABX
Connect the right terminal of the 1st extension to terminal 1 of the
CALLER-ID terminal board. Connect the right terminal of the 2nd
terminal to terminal 2 of the CALLER-ID terminal board. Repeat the
connection up to the 4th extension. You can choose any of the
extensions, as long as you comply with the correct sequence (i.e. right
terminal of DER 41 connected to terminal 1 of the CALLER-ID terminal
board, right terminal of DER 43 connected to terminal 2, right terminal
of DER 45 connected to terminal 3, right terminal of DER 46 connected
to terminal 4).
Warning: If the telephone installation includes the ISDN interface board,
for the correct operation of the ES70 check that the microcontroller of the
FT105P or FT208P PABX is provided with H301 or G301 software or
higher.
4
2
3
1
CALLER - ID
URB2 URB1
4
2
3
1
CALLER - ID
URB2 URB1
JP4
JP201
GND MUS
EXT + 5V
GND AMP
EXT
DER48
DER45
DER46
DER43
DER44
DER47
DER42 DER41
J204
IL COPERCHIO
CAUTION:TO PREVENT THE
RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER
RISCHIO DI SCOSSE ELET-
ATTENZIONE: PER EVITARE
TRICHE NON RIMUOVERE
DANGER
4
2
3
1
CALLER - ID
URB2 URB1
G301
W1
J204
6A
NA2
6B
NC2
3
NA3
2
NC3
1
C3
4
C4
5
NA4
C2
NC4
Installation of the ES60 (or ES65) intercom interface and ES70
caller identifier board in the FT105P or FT208P PABX.
ES60
ES65
ES70
PABX
PROGRAMMING
You need to enter the number of each extension you require the service
for. It is recommended to note down the type of programming in the
enclosed table.
0 service disabled
1 service enabled
Program:
pick up the handset of the extension 41 (dialling tone);
dial the access code 333316;
- (only FT105P) – dial 5 digits to program 5 extensions (see Table).
Always dial a number of 5 digits even if extensions are less than
5.
- (only FT208P) – dial 8 digits to program 8 extensions (see Table).
Always dial a number of 8 digits even if extensions are less than
8.
wait for the acknowledgment tone and hang up.
Notes
The caller ID service will not work if the external lines are pro-
grammed for direct dialling (DISA) (see page 14 of the PABX techni-
cal manual for DISA programming).
The maximum number of extensions with the caller ID function is
4. If a higher number of telephones is enabled during programming, the
exchanger will automatically recognise only the first 4 telephones and
exclude the others from the service.
Connection of the FT105P or FT208P PABX with the ES70 caller
identifier board.
4
CALLER - ID
Art.FT105P
FT208P
URB1
URB1
DER41
DER43
DER45
DER47
DER42
DER44
DER46
DER48
3 2 1
URB2
URB2
Art.ES70
I
NTERCOMS *
V
IDEOINTERCOMS *
T
ELECOMMUNICA
TION
F
A
R
T
E
L
EXPANSION BOARDS
ES70. Caller identifier board
