background image

 

USE AND MAINTENANCE MANUAL - SECTION 1 

 

AERIAL PLATFORM ELEVAH 70 - Rev. 04_2020 

Page 1-4 

 

Danger of overturning 

 

  Do not lift the work platform on a slope or on irregular or soft surfaces. 

  Before driving the machine on floors, bridges, lorries and other surfaces, check their maximum 

capacity values. 

  Do not exceed the maximum capacity of the machine. Evenly distribute the loads on the floor of 

the work platform as best as possible. 

  Keep the machine chassis (including stabilisers) at a minimum distance of 0.5 m from holes, 

unevenness, descents, obstacles, debris, hidden holes and other potential dangers found at 

ground level. 

  Do not attempt to use the machine as a crane. Do not tie the machine to an adjacent structure. 

  Do not increase the dimension of the working platform with unauthorised extensions or by 

extending the platform. 

  If the extending structure or the work platform remains jammed so that one or more wheels are 

lifted from the ground, the operator is required to climb off the working platform before attempting 
to free the machine.  To stabilise the machine and have personnel climb down from the work 

platform, use a crane, forklift trucks or other adequate equipment. 

  Do not move the machine with the stabilisers inserted and the extendible structure lifted. Before 

moving the machine, completely lower the extendible structure. 

 

Danger of crushing and impact 

 

 

  When using the machine or lifting or lowering the work platform, check the distances above, at 

the sides and below the said platform. 

  Do not lean out of the rails of the work platform when the machine is running. 

  Always pay maximum attention to avoid any obstacles from hitting the operational controls and 

people on the work platform or from interfering with them. 

  Make sure the operators of other machines, overhead or at ground level, are informed of the 

presence of the machine. 

  Warn personnel not to work, stand or transit underneath the lifted platform. Mark off the floor 

area with appropriate barriers, as required. 

 
 

 

Содержание ELEVAH 70































































Отзывы: