Fancom MRK.2, Руководство пользователя

Страница: 17 / 33

US and CAN type:
when using 3 phase power supply 240/3/60.
also connect L2 to N.
SEAL ALL CABLE ENTRIES
IMPORTANT!!!
All the equipment
must be grounded correctly
Connect Fancom equipment according to the prevailing
standards of the local electricity company.
M
N L
N L1 L2 L3 U V W
Datum: 27-11-95
By:RvW / Ref:VJ scale: nvt
Subject:
Update / by check / by
Version:
Sheet ... of ...
M
V
W
U
N L1 L2 L3 U V W
+ -
+ -
cl op
GND + L - +
cl COM op
1 2 3 4 5
6
7 8
9 10
1 2 3 4
5 6 7
cl op GND + L - + COM op
1 2 3 4
5 6 7
CLOSE
OPEN
N/L2
CLOSE
OPEN
Limit switches
LOW VOLTAGE
HIGH VOLTAGE
Motor
Protection
Switch
Connection diagram MRK.2 with 10-0 / 0-10Vdc control
Control
0-10V/10-0V
Doc.no: 03.08.548.07
Connection MRK.2
with 0 - 10V control
CLOSE
OPEN
Limit switches
LOW VOLTAGE
HIGH VOLTAGE
Motor
protection
switch
close (-)
open (+)
Control
0-10V/10-0V
4K7
Damper
position
feedback
380-400Vac motor
[240/3/50-60] motor
240/1/50-60 motor
[120/1/50-60] motor
MOTOR
240/1/50-60
[120/1/50-60]
max 4A
MOTOR
380-400Vac
[240/3/50-60]
max 4A
[L2] [L1] [L2] [L3]
220/400Vac
[240/3/50-60]
L1 L2 L3
240/1/50-60
[120/1/50-60]
[N] [H]
N/L2 L1
U.S. --> The power supply voltage and the transformer voltage must be the same
U.S. --> The frequency of the power supply voltage and the motor frequency must be the same.
REMARK:
(T1)
(T2)
(T3)
N
1 2 3 4 5 6 7 8 9 10
cl
Only for US and CAN models
Fuse only necessary when power
voltage is 240Vac (L1 and L2)
Fuse is F1A - 250V
F1A/250 V
F1
F1A/250 V
F2
F1A/250 V
F1
F1A/250 V
F2
Technical modifications reserved
Only for US and CA models
Fuse only necessary when power
voltage is 240Vac (L1 and L2)
Fuse is F1A - 250V
3x0.8mm
22AWG
3x0.8mm
22AWG
4x2,5mm2
12AWG
5x2,5mm2
12AWG
2x0.8mm
22AWG
3x0.8mm
22AWG
3x0.8mm
22AWG
2x0.8mm
22AWG
close (-)
open (+)
4K7
Damper
position
feedback
cl op
GND
+
L
-
+ cl COM op
4x2,5mm2
12AWG
3x2,5mm2
12AWG
File:Aansl. MRK 2/GB
Fancom bv.
agro computers
P.O. box 7131
5980 AC Panningen
The Netherlands
If limit switches are included in the motor circuit, the
limit switch connections on the print should be connected.
29-3-00 / VJa JRe/VJa