FALMEC Sintesi 90, Инструкция пользователя

Страница: 19 / 56

19
ENGLISH
.
Unconfigured in-
duction module (all
induction module
answer to UI, but
any element is rela-
ted to the effected
cooking zone.)
induction module
is not configured
Delete the hob configu-
ration and activate the
manual configuration.
Start the UI service
menu to configure the
induction module if the
listed points are not
successful replace the
module.
.
No communication
between UI and
induction module
No power supply
of induction
module.
Bad cabling or
defect
Check power and LIN
connections. If con-
nection is OK, replace
the module
.
Main power distur-
bance
1. Failure in main
power frequency
detection
2. Overvoltage
Check main power
voltage and frequency,
if ok replace the module
.
Non assignable
failure
Replace module or User
interface
.
Fan failure Fan or control
electronic is defect
Replace the module
.
Defect ive tempe-
rature probe on
inductor
Sensor signal out
of valid range; sen-
sor or electronic is
defect
Replace the module
.
Hardware defect of
induction module
Defect hardware
device detected
by the self-check
of the module
Replace the module
.
Configuration failure 2 cooking zones
are delicated to
the same element
of the UI
Delete the actual confi-
guration
manual configuration
with service menu
.
Fixed sensor value
(test function for T
probe on inductor)
Not enough tem-
perature change
(10 K) within 5 min
after switch on
the hob
System must cool down
No
functiona-
lity and no
displaying
Overvoltage on
the switch mode
power supply (no
functionality)
400 V connection Disconnect and correct
the power line con-
nection
Note:
Not each failure can be delected automatically by the system, e.g. in case of defect of the
User interface power supply.
CLEANING AND MAINTENANCE INSTRUCTIONS
ATTENTION!
For cleaning, never use a steam equipment.
Before cleaning the cooker, make sure that it is at room temperature.
Always clean the cooker after each use with a specific cleanser for pyroceram.
Do not use products containing:
- corrosive agents (soda, acids, ammoniac).
- abrasive agents (dusts or paste).
Do not use pointed or abrasive objects.
After cleaning, dry the appliance with a soft cloth.
If the appliance is built-in over an oven or an electric kitchen fitted with pyrolytic system
do not operate it while the pyrolytic procedure is under way, as the overheating protec-
tion of the cooker can be released (see relevant chapter).
DISPOSAL AFTER END OF USEFUL LIFE
The crossed-out wheeled bin symbol on the appliance means that
the product
is WEEE , i.e. " Waste electrical and electronic equipment", accordingly it must not
be disposed of with unsorted waste (i.e. with "mixed household waste"), but it
must be disposed of separately so that it can undergo specific operations for its
re-use, or a specific treatment, to remove and safely dispose of any substances that may be
harmful to the environment and remove the raw materials that can be recycled. Proper dis-
posal of these products contributes to saving valuable resources and avoid potential nega-
tive effects on personal health and the environment, which may be caused by inappropriate
disposal of waste.
You are kindly asked to contact your local authorities for further information regarding the
designated waste collection points nearest to you. Penalties for improper disposal of such
waste can be applied in compliance with national regulations.
INFORMATION ON DISPOSAL IN EUROPEAN UNION COUNTRIES
The EU WEEE Directive was implemented differently in each country, accordingly, if you wish
to dispose of this appliance we suggest contacting your local authorities or dealer to find
out what the correct method of disposal is.
INFORMATION ON DISPOSAL IN NON-EUROPEAN UNION COUNTRIES
The crossed-out trash or refuse bin symbol is only valid in the European Union: if you wish
to dispose of this appliance in other countries, we suggest contacting your local authorities
or dealer to find out what the correct method of disposal is.
WARNING!
The Manufacturer reserves the right to make changes to the equipment at any time and
without prior notice. Printing, translation and reproduction, even partial, of this manual are
bound by the Manufacturer's authorisation.
Technical information, graphic representations and specifications in this manual are for in-
formation purposes and cannot be divulged.
This manual is written in Italian. The Manufacturer is not responsible for any transcription
or translation errors.