14
MAINTENANCE
Before cleaning or carrying out maintenance operations,
disconnect the equipment by removing the plug or
switching off the main switch.
Do not use detergents containing abrasive, acidic or corrosive
substances or abrasive cloths.
Regular maintenance guarantees proper operation and performance
over time.
Special attention is to be paid to the
metal anti-grease filters
: fre-
quent cleaning of the filters and their supports ensures that no flam-
mable grease is accumulated.
CLEANING OF EXTERNAL SURFACES
You are advised to clean the external surfaces of the hood
at least once
every 15 days
to prevent oily substances and grease from sticking to
them.
Alternatively
and for all the other types of surfaces
, it can be cleaned
using a damp cloth, slightly moistened with mild, liquid detergent or
denatured alcohol.
Finish off cleaning by rinsing well and drying with soft cloths.
Do not use too much water next to the push button con-
trol panel and lighting devices in order to prevent humid-
ity from reaching electronic parts.
The glass panels can only be cleaned with specific, non-corrosive or
non-abrasive detergents using a soft cloth.
The Manufacturer declines all responsibility for failure to comply with
these instructions.
CLEANING OF INTERNAL SURFACES
It is forbidden to clean electrical parts, or parts related to
the motor inside the hood, with liquids or solvents.
For the internal metal parts, see the previous paragraph.
METAL ANTI-GREASE FILTERS
It is advised to
frequently
wash the metal filters (
at least once a
month
) leaving them to soak in boiling water and washing up liquid
for 1 hour, taking care not to bend them.
Do not use corrosive, acid or alkaline detergents.
Rinse them well and wait for them to be completely dry before reas-
sembling them.
They are dishwasher safe.
To extract and insert the metal anti-grease filters see the picture.
1
2
LIGHTING
The range hood is equipped with high efficiency, low consumption LED
spotlights with extremely long duration under normal use conditions.
Should the LED spotlight need to be replaced, proceed as shown in
the figure.
12V
3
1
2
GREASE DRIP TRAY
It is advisable to clean the tray every 15 days.
Do not use corrosive, acid or alkaline detergents.
For more thorough cleaning, remove the oil collection tray (see figure)
and wash it with hot water and washing up liquid. Rinse it well and wait
for it to be completely dry before reassembling it. They are dishwasher
safe.
3
2
1
DISPOSAL AFTER END OF USEFUL LIFE
The crossed-out trash or refuse bin symbol on the appliance
means that
the product is WEEE
, i.e.
“
Waste electrical and
electronic equipment'', accordingly
it must not be disposed
of with regular unsorted waste
(i.e. with ''mixed household
waste''), but it must be disposed of separately so that it can undergo
specific processing for its re-use, or a specific treatment, to remove and
safely dispose of any substances that may be harmful to the environ-
ment and remove the raw materials that can be recycled. Proper dis-
posal of these products contributes to saving valuable resources and
avoid potential negative effects on personal health and the environ-
ment, which may be caused by inappropriate disposal of waste.
You are kindly asked to contact your local authorities for further infor-
mation regarding the designated waste collection points nearest to
you. Penalties for improper disposal of such waste can be applied in
compliance with national regulations.
INFORMATION ON DISPOSAL IN EUROPEAN UNION COUNTRIES
The EU WEEE Directive was implemented differently in each country,
accordingly, if you wish to dispose of this appliance we suggest con-
tacting your local authorities or dealer to find out what the correct
method of disposal is.
INFORMATION ON DISPOSAL IN NON-EUROPEAN UNION COUN-
TRIES
The crossed-out trash or refuse bin symbol is only valid in the European
Union: if you wish to dispose of this appliance in other countries, we
suggest contacting your local authorities or dealer to find out what the
correct method of disposal is.
WARNING!
The Manufacturer reserves the right to make changes to the equip-
ment at any time and without prior notice. Printing, translation and
reproduction, even partial, of this manual are bound by the Manufac-
turer's authorisation.
Technical information, graphic representations and specifications in
this manual are for information purposes and cannot be divulged.
This manual is written in Italian. The Manufacturer is not responsible for
any transcription or translation errors.
